Personal Safety - Silverline 265438 Mode D'emploi

265438
c) Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the rate
for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must be
repaired.
c) Disconnect the plug from the power source and/or the battery pack from
the power tool before making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tool's operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with
these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
1500W Steam Cleaning System
Steam Cleaner Safety
WARNING: Danger of scalding
• Before starting the machine check that the power cord, plug and steam hose
are in good condition
• If an extension lead is used, the plug and socket must be of watertight
construction. An inadequate extension lead can be dangerous
• Never splash, wash down or plunge the steam cleaner into water or any other
liquid
• Never obstruct the steam outlet or nozzle
• Never direct the steam nozzle towards people, animals, trees or towards
particularly hot or cold objects
• Never use steam to clean objects containing hazardous substances, for
example asbestos or dried chemicals that may be re-activated with steam; for
example, glue
• Do not attempt to clean an electric cooker when the cooker is on
• Do not clean household appliances, electronic equipment or electrical
connections such as the interior of ovens, sockets, control boards etc. with this
steam cleaner
• There are no user-serviceable parts inside. In case of malfunction, the machine
must be repaired by trained technicians only. Take the cleaner to an approved
service centre
• Ensure all users have read and fully understand the instruction manual
• Do not work with wet hands
• Do not cover the steam cleaner when in use, it may over-heat
• Keep the steam cleaner upright and use on a flat surface
• Remove the plug from the mains socket before replacing any accessory or
when you are not using the machine
• Never attempt to change accessories before the steam has stopped spraying
out of the nozzle
• The appliance is not to be used if it has been dropped, if there are any visible
signs of damage or if it is leaking
• Keep the appliance out of reach of children whilst it is energising or cooling
down
www.silverlinetools.com
5