Publicité
Les langues disponibles
Les langues disponibles
FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.
This insTrucTion Manual conTains
iMporTanT safeTy inforMaTion.
read This
insTrucTion Manual
carefully and
undersTand all
inforMaTion Before
operaTing This Tool.
• Always operate, inspect and maintain
this tool in accordance with American
National Standards Institute Safety
Code of Portable Air Tools (ANSI B186.1)
and any other applicable safety
codes and regulations.
• For safety, top
performance and
maximum durability of
parts, operate this tool
at 90 psig; 6.2 bar max
air pressure with 1/2"
diameter air supply
hose.
• Always wear impact-
resistant eye and
face protection when
operating or performing
maintenance on this tool
(users and bystanders).
• High sound levels can
cause permanent
hearing loss. Always
use hearing protection
as recommended by
your employer and
OSHA regulations while using this tool
(users and bystanders).
• Keep the tool in efficient operating
condition.
• Operators and maintenance personnel
must be physically able to handle the
bulk, weight and power of this tool.
• Air powered tools can
vibrate during use.
Extended exposure to
vibration, repetitive
motions, or
uncomfortable positions
during use may be harmful to your hands
and arms. Discontinue use of tool if
discomfort, tingling, or pain occurs. Seek
medical advice before resuming use.
SX556-2 / SX556-6
WARNING
• Compressed air can
cause severe injury.
Never direct air at
yourself or others.
Always turn off the
air supply, drain hose
of air pressure and
detach tool from air
supply before installing,
removing or adjusting
any part or accessory on
this tool, or before
performing any
maintenance on this
tool. Failure to do so
could result in injury.
Whip hoses can cause
serious injury. Always
check for and replace
any damaged, frayed
or loose hoses and fittings. Do not
operate a damaged or worn tool. Do
not use quick-detach couplings at tool.
See instructions for correct set-up.
• Place the tool on the work before
starting the tool. Do not point or
indulge in any horseplay with this tool.
• Note direction of rotation BEFORE
operating this tool.
• Slipping, tripping
and/or falling while
operating air tools can
be a major cause of
serious injury or death.
Be aware of excess hose
left on the walking or work surface.
• Keep body working stance balanced
and firm. Do not overreach when
operating the tool.
• Keep tool out of reach of children.
• Anticipate and be alert for sudden
changes in motion during use of any
power tool.
• Do not carry tool by the
hose. Protect the hose
from sharp objects and
heat.
• Tool shaft may continue
to rotate briefly after
throttle is released. Avoid direct contact
with accessories during and after use.
Gloves will reduce the risk of cuts or burns.
2
• Keep away from
rotating end of tool.
Do not wear jewelry or
loose clothing. Secure
long hair. Scalping can
occur if hair is not kept
away from tool and
accessories. Choking can
occur if neckwear is not
kept away from tool
and accessories.
• Do not lubricate tools
with flammable or volatile
liquids such as kerosene,
diesel or jet fuel.
• This tool is not insulated
against electric shock.
• This tool must not be
used in explosive
atmospheres.
• Impact wrenches are not
torque control devices.
Fasteners with specific
torque requirements must be checked
with suitable torque measuring devices
after installation with an impact wrench.
• Use only impact wrench sockets and
accessories on this tool. Do not use
hand sockets and accessories.
• Do not force tool beyond its rated
capacity.
• Do not use (or modify) the tool for
any other purpose than that for which
it was designed without consulting the
manufacturer's authorized representative.
• Do not remove any labels. Replace
damaged labels.
• Use accessories recommended by
Sunex Tools
®
.
• This product may contain chemicals
known to the State of California to
cause cancer and birth defects or other
reproductive harm. Wash hands
thoroughly after handling.
03/13/14
Publicité
