Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
ACTIVE SPEAKER
Installation Instructions
Important Safety Information
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
When drilling or cutting, always check what is on the opposite
side of the surface.
Tools Needed
• Pencil
• Drill
1
• 3 mm (
/
in.) drill bit
8
1
• 13 mm (
/
in.) drill bit
2
• Phillips screwdriver
• Rotary cutting tool or jigsaw
• Marine sealant (optional)
Mounting Considerations
This device should be mounted in a location that is not exposed
to extreme temperatures or conditions. The temperature range
for this device is listed in the product specifications. Extended
exposure to temperatures exceeding the specified temperature
range, in storage or operating conditions, may cause device
failure. Extreme-temperature-induced damage and related
consequences are not covered by the warranty.
When selecting a mounting location for the active speaker,
observe these considerations.
• To avoid interference with a magnetic compass, do not install
the active speaker closer than 50 cm (19.6 in.) to a compass.
• You must install the active speaker inline with a GHS
handset.
• You must install the active speaker within 1.2 m (48 in.) of the
location you want to connect the GHS 11 handset.
• You must use an extension cable (not included) to connect
the active speaker to the VHF radio. Extension cables are
available from your Garmin
extension cable, you must verify that the cable is long
enough to reach the mounting location for the speaker and
connect to the VHF radio.
Mounting the Active Speaker
Be careful when cutting the hole to mount the speaker. There is
only a small amount of clearance between the case and the
mounting holes, and cutting the hole too large could
compromise the stability of the speaker after it is mounted.
Before you can mount the speaker, you must select a mounting
location.
1
Trim the template and make sure it fits at the mounting
location.
2
Secure the template to the mounting surface.
1
3
Using a 13 mm (
/
in.) drill bit, drill a hole inside the corner of
2
the line on the template to prepare the mounting surface for
cutting.
4
Using a rotary-cutting tool or jigsaw, cut the mounting surface
along the inside of the dashed line on the template.
5
Place the speaker in the cutout to test the fit.
2
CAUTION
NOTICE
NOTICE
dealer. When selecting an
®
NOTICE
6
If necessary, use a file and sandpaper to refine the size of
the cutout.
7
After the speaker fits correctly in the cutout, ensure the
mounting holes on the speaker line up with the pilot holes on
the template.
8
If the mounting holes on the speaker do not line up, mark the
new pilot-hole locations.
9
Using a 3 mm (
10
Remove the template from the mounting surface.
11
Install the included mounting gasket
speaker.
12
Make the necessary wiring connections
Active Speaker to the VHF Radio and Handset, page
13
Place the speaker in the cutout.
14
Secure the speaker to the mounting surface using the
included M4 screws
15
Snap the screw cover
Installing the Handset Connector in the Mounting
Surface
Before drilling a hole to mount the handset connector from the
active speaker, you should mount the active speaker and verify
that the cable from the active speaker is long enough to reach
the handset-connector mounting location
Speaker, page
11
™
1
Using the mounting plate
hole in the center of the mounting plate and mark the screw
locations.
2
Set the mounting plate aside.
Do not drill through the mounting plate.
3
Using a 22 mm (
cable hole
4
Using a 3 mm (
5
Apply marine sealant between the mounting plate and the
mounting surface to help seal the holes (optional).
6
Using the included screws, attach the mounting plate to the
mounting surface.
7
Route the long cable from the active speaker to the
connector mounting location.
8
Feed the connector
surface.
9
Apply marine sealant around the connector in the mounting
plate to help seal the hole (optional).
1
/
in.) drill bit, drill the pilot holes.
8
.
in place.
2).
as a template, trace the cable
7
/
in.) drill bit or hole saw, drill the center
8
in the mounting surface.
1
/
in.) drill bit, drill the pilot holes.
8
through the back of the mounting
on the back of the
(Connecting the
3).
(Mounting the Active
Installation Instructions
Publicité
Table des Matières
