Publicité
Les langues disponibles
Les langues disponibles
Operating instructions
BS-2.0/1m borescope camera sensor
Item no. 2139964
Intended use
This product serves as a camera attachment for borescopes with interchangeable borescope
camera sensors for optical troubleshooting or inspection of de-energised systems and equip-
ment. The four LEDs integrated in the camera head enable recordings or photos in totally dark
areas. The brightness can be adjusted via the connected borescope. The camera sensor is
waterproof up to the marking (IP67) and perfectly suitable for use in de-energised liquids (no
acids or bases).
It is forbidden to use the product on people and animals and in potentially explosive environ-
ments. The power is supplied via the respective connected borescope.
For safety and approval purposes, you must not rebuild and/or modify this product. Using the
product for purposes other than those described above may damage the product. Furthermore,
improper use may cause risks such as short-circuit, fire, electric shock, injuries, etc.
The borescope is not a medical product and is not approved for use on people and animals.
Read the operating instructions carefully and store them in a safe place. Only make this product
available to third parties together with its operating instructions.
This product complies with statutory, national and European regulations. All company names
and product names are trademarks of their respective owners. All rights reserved.
Package contents
• Flexible camera sensor
• Case
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the
QR code. Follow the instructions on the website.
Explanation of symbols
The triangle containing a lightning symbol warns against danger of electric shock or
impairment of the electrical safety of the device.
In the operating manual, an exclamation mark inside a triangle indicates important
instructions.
The arrow symbol indicates special information and advice on operating the device.
This product has been CE tested and complies with the necessary national and
European regulations.
Safety instructions
This quick start contains important information on how to use the transistor
tester. Please read it carefully before using the device for the first time.
• Damage caused due to failure to observe these instructions will void the warranty.
We shall not be liable for any consequential damages!
• We shall not be liable for damage to property or personal injury caused by incor-
rect handling or failure to observe the safety information! Such cases will void the
warranty/guarantee
a) Persons / product
• This product is a precision instrument. Do not drop it or expose it to impacts.
• This product is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. It may become a dange-
rous plaything for children.
• Protect the product from extreme temperatures, direct sunlight, strong vibrations,
high humidity, moisture, combustible gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• Caution, LED light source: Do not look directly at the LED light! Do not look into the
beam directly or with optical instruments!
• If safe operation is no longer possible, take the product out of service and secure it
against unintended use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stress.
• Handle the product carefully. The product can be damaged if crushed, struck or
dropped, even from a low height.
• Always observe the safety instructions and operating instructions of any other
devices which are connected to the product.
• Observe the statutory regulations relating to the use of the product. Do not use the
product for the surveillance of people or vehicles!
b) Other information
• Contact an expert when in doubt about the operation, safety or connection of the
product.
• Maintenance, adjustment and repair work may be carried out only by an expert or
a specialist workshop.
• If in doubt about how to connect the device correctly, or should any questions arise
that are not answered in these operating instructions, please contact our technical
service or another specialist.
Connection
Only the camera sensor may be submerged in de-energised liquids. The camera
sensor must not be submerged above the marking "IP67 max. water level". The
socket area must always stay dry.
The camera sensor must only be used for inspection in de-energised equipment.
The camera sensor is made of metal and this may lead to short-circuits. For safety
reasons, turn off all power sources before each inspection.
Avoid heavy mechanical loads and vibrations.
1. Turn off the borescope.
2. Insert the plug of the camera sensor (with metal nose) into the connection socket of the
borescope. The metal nose of the plug only fits into the socket on the correct side. Secure
the plug connection with the screw sleeve on the borescope by turning it clockwise.
3. Make sure the connection socket is aligned exactly with the pins of the connection plug. The
metal nose of the plug only fits into the socket on the correct side.
4. Turn on the borescope.
5. Proceed in reverse order to disconnect the camera sensor from the borescope.
Information about controlling the LED brightness can be found in the operating in-
structions of the borescope.
Cleaning
• To clean the camera lens, use a soft cloth or a cleaning swab.
• Clean the camera sensor using a soft, damp cleaning cloth. Always store the well-dried
camera sensor in the carrier bag provided to avoid damage.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the house-
hold waste.
At the end of its service life, dispose of the product in accordance with applicable
regulatory guidelines.
Technical data
Compatible with ................ BS-300XRSD, BS-350XIPSD, BS-30XHR, BS-200XW, BS-100XIP
Resolution ......................... 400 x 400 pixels
Lighting ............................. 4 white LEDs
Video frame rate ............... 30 fps
Protection class ................ IP67 (camera sensor)
Field of view ...................... 120°
Focusing ........................... 5 – 50 mm
Lighting ............................. automatic
White balance ................... automatic
Operating conditions ......... 0 to +45 °C, 15 – 85% RH
Storage conditions ............ -10 to +50 °C, 15 – 85% RH
Camera head Ø ................ 2 mm
Min. bending radius .......... 20 mm
Length............................... 1 m
Weight .............................. approx. 35 g (camera sensor), approx. 1000 g (case)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
© Copyright 2019 by Conrad Electronic SE.
2139964_V1_1019_02_m_VTP_en
Publicité
