Cleaning The Tool - SNOWJOE SunJoe 24V-PS8-CT Manuel D'utilisation

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

18. Check for damaged parts – Before further use of the
appliance, all guards and parts should be carefully
checked to determine that it will operate properly and
perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting, and any other condition that may affect its
operation. A guard or other part that is damaged should
be properly repaired or replaced. Contact the Snow Joe
+ Sun Joe
customer service center at 1-866-SNOWJOE
®
(1-866-766-9563) for assistance.
19. Maintain the power tool with care – Keep the cutting
edges sharp and clean for optimal performance and to
reduce the risk of injury. Keep the handles dry, clean,
and free from oil and grease. Follow the additional
recommendations described in the maintenance section
of this manual.
20. Do not use the power tool if the switch does not turn it on
and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
21. Keep all parts of the body away from the cutting blades or
chain. Do not remove cut material or hold material to be cut
when blades are moving. Make sure the switch is off when
clearing jammed material. The blades or chain will continue
moving for a while after the tool is turned off. A moment
of inattention while operating the power tool may result in
serious personal injury.
22. Carry the power tool by the handle with the cutting blade
or chain stopped. When transporting or storing the power
tool, always keep the blades or chain bar covered. Proper
handling of the pole chain saw will reduce possible
personal injury from the cutting blades or chain.
23. Hold the product by insulated gripping surfaces only,
because the cutting blade or chain may contact hidden
wiring. Cutting blades or chain contacting a "live" wire
may make exposed metal parts of the product "live"and
could give the operator an electric shock.
24. The unit has not been designed to provide protection
from electric shock in the event of contact with overhead
electric lines. Never use the power tool near any electrical
power lines. Contact with or use near power lines may
cause serious injury or electric shock resulting in death.
Maintain a minimum clearance of 50 ft (15 m) from all
power lines.
m
WARNING!
Before inspecting, cleaning, or servicing
the machine, remove the battery and wait for all moving parts
to stop. Failure to follow these instructions can result in serious
personal injury or property damage.
m
WARNING!
Do not use this appliance without reading
this instruction manual.
m
WARNING!
Do not use the appliance within range of
persons unless they are wearing protective clothing.
m
WARNING!
Do not operate the cordless power tool in
a tree, on a ladder, or on a scaffold. Using the tool under such
circumstances is extremely dangerous.
m
WARNING!
Do not let familiarity with this type of tool
prevent you from taking all necessary precautions. Remember
that a careless fraction of a second is sufficient to inflict
serious injury.
m
WARNING!
The cordless pole chain saw must be fully
assembled before operation! Do not use the tool that is only
®
partly assembled or assembled with damaged parts!
m
WARNING!
Starting, stopping, and restarting an electric
motor repeatedly within a few seconds can generate a great
deal of heat and damage the motor. To protect the life of your
cordless power tool, always wait at least five seconds after
stopping before restarting the unit.
m
WARNING!
Electrical Shock Hazard – Before starting
up your machine, please check it carefully for any defects. If
you find any, do not start up your machine and contact your
distributor.
NOTE: Take care of small parts that are removed during
assembly or when making adjustments. Keep them secure to
avoid loss.
Please contact an authorized Snow Joe
or call the Snow Joe
at 1-866-SNOWJOE (1-866-766-9563) for all maintenance
or operations not foreseen in this manual. Any operation
performed in an unauthorized service center or by unqualified
personnel will completely invalidate the warranty.
m
WARNING!
For your safety and that of others:
• Correct maintenance is essential to maintain the original
efficiency and safety of the machine over time.
• Keep all nuts, bolts, and screws tight to be sure the
equipment is in safe working condition.
• Never use the machine with worn or damaged parts.
Damaged parts are to be replaced and never repaired.
m
WARNING!
Always wear protective gloves during
maintenance operations.
m
WARNING!
Use only original manufacturer's
replacement parts, accessories and attachments. Failure to do
so can cause possible injury and poor performance.
To order genuine replacement parts or accessories for the
Sun Joe
iON+ cordless pole chain saw, please visit
®
sunjoe.com or contact the Snow Joe
service center at 1-866-SNOWJOE (1-866-766-9563).

Cleaning the Tool

m
WARNING!
Never let any liquid get inside the motor
housing and NEVER immerse any part of the housing in liquid.
1. Stop the motor and remove the battery.
2. Clean dirt and debris from the body of the tool, using a
damp cloth with a mild detergent.
2
+ Sun Joe
®
+ Sun Joe
customer service center
®
®
+ Sun Joe
®
dealer
®
customer
®

Publicité

Table des Matières
loading

Table des Matières