VONROC LM502AC Traduction De La Notice Originale page 11

4. Power socket
5. Cable strain relief
6. Cable holder
7. Carrying handle
8. Wheel
9. Wheel cover
10. Grass box basket
11. Grass box lid
12. Grass box cover
13. Grass level indicator
14. Lower handle
15. Knob for handle
16. Grass box carrying handle
3. ASSEMBLY
Before assembly, always switch off the
machine and remove the mains plug from
the mains.
Assembling the lower handle (Fig. A, B, C)
1. Insert the lower handle (14) into the intended
hole of the lawn mower body, as shown on figu-
re B. Ensure the hole in the lower handle (14)
aligns with the hole in the lawn mower body.
2. Insert the screw in the hole and tighten by turn-
ing clockwise, as shown on figure C.
3. Repeat these steps for the other lower handle
(14).
Assembling the upper handle (Fig. A, D, E, F)
1. Put the cable strain relief (5) on the right side of
the upper handle (1) as shown on figure D.
2. Attach the upper handle (1) to the lower handle
(14), using the supplied bolts and handle knobs
(15) as shown on figure E. Make sure the on/off
switch (2) assembly is on the right side when
standing behind the lawn mower.
3. Fixate the cable to the handle by using the
cable holders (6), as shown on figure F.
Note: When handle knobs (15) are loosened, the up-
per handle (1) can be folded down for storing the lawn
mower. Ensure that the power cable is not caught.
Mounting the wheels (Fig. A, G)
1. Attach a wheel (8) on the axle. Afterwards, put a
supplied metal washer onto the axle.
2. Insert the supplied metal split pin in the ope-
ning of the axle. Afterwards, fold the metal split
pin around the axle, as shown on figure G.
WWW.VONROC.COM
3. Mount the wheel cover (9) onto the wheel (8).
Make sure the plastic pins on the wheel cover
(9) align with the holes of the wheel (8).
4. Repeat these steps for the other wheels.
Assembling the grass box (Fig. A, H, I, J, K)
It is possible to use the lawn mower with or without
grass box. Remember though that when cutting
without the grass box, the grass box lid (11) must
be lowered. Do not operate the mower with outlet
lid lifted.
1. Mount the Grass box carrying handle (16) onto
the grass box cover (12), as shown on figure H.
2. Join the two halves of the grass box basket
(10), as shown on figure I.
3. Mount the grass box cover (12) onto the assem-
bled grass box basket (10), as shown on figure J.
4. Lift the grass box lid (11) and attach the assem-
bled grass box onto the lawn mower. Ensure the
indents in the grass box align properly with the
holders of the lawn mower body.
Note: the grass box is fitted with a grass level
indicator (13), which shows the amount of mowed
grass. As long as the grass box is not full, the indi-
cator will be opened. When the grass box is full, the
indicator will close. In that case immediately stop
mowing and empty the grass box. This indicator is
only a rough guideline, of which the functionality
depends on the condition inside the grass basket.
Replacing the cutting blade (Fig. A, P)
Before carrying out any work on the
machine, disconnect the mains plug from
the power supply.
When replacing the cutting blade, wear
protective gloves. Danger of injury when
touching the cutting blade.
Only use blades that are recommended by
the manufacturer.
1. Remove the grass box.
2. Turn the mower onto its side.
3. Firmly hold cutting blade using protective gloves.
4. Turn the cutting blade fixing screw coun-
ter-clockwise to loosen it, as shown on figure P.
5. Replace or sharpen the cutting blade.
6. Install the cutting blade, use the above pro-
cedure in reversed order (holes in the cutting
EN
11