Important - Bissell STAINPRO 4 Mode D'emploi

C-4 Empty the 2-in-1 water
tank/clean removable nozzle
1. Turn power switch OFF. Remove the 2-in-
1 water tank from the base using the tank
carry handle. Carry the tank like a bucket
to a utility sink or outside where you will
dispose of the collection water. Remove
the top of the tank by rotating the handle
forward to unlatch lid and lifting lid off tank.
2. Empty collection water from bottom of
tank.
3. After each use, remove and rinse the lint
screen located on the tank lid.
4. If nozzle needs to be cleaned, remove by
grasping handle at the top and pulling out.
Clean removable nozzle by rinsing under
running water.
5. When finished, replace nozzle by slightly
raising front of machine to line up slots on
the base with the hooks on nozzle. Attach at
base first and then click nozzle into place.
NOTE: If nozzle is not attached properly
loss of suction will occur.
6. Refill bladder with water and formula and
continue cleaning.
C-5 ReadyTools™
Your deep cleaner comes equipped with
a hose and at least one attachment for
cleaning stairs, upholstery, and more.
Important! If using the machine to clean
upholstery, check upholstery tags.
1. Check manufacturer's tag before cleaning.
"W" or "WS" on the tag means you can use
your deep cleaner. If the tag is coded with
"X" or "S" (with a diagonal strike through),
or says "Dry Clean Only," do not proceed. Do
not use on velvet or silk. If manufacturer's
tag is missing or not coded, check with your
furniture dealer.
2. Check for colourfastness in an
inconspicuous place.
3. If possible, check upholstery stuffing.
Coloured stuffing may bleed through fabric
when wet.
4. Plan activities to give upholstery time to
dry.
5. Vacuum thoroughly to pick up loose
debris and pet hair. Use a vacuum with a
brush attachment and a crevice tool to clean
in fabric folds and tufts.
6. To begin cleaning with attachments,
follow the instructions in section C-1 for
filling the 2-in-1 water tank.
8
www.BISSELL.com
7. Set the ReadyTools™ dial to the TOOLS
setting. This will allow spray and suction
from the hose.
8. Attach the cleaning tool to the end of the
hose.
9. Clean by pressing the spray trigger to
spray solution onto the area to be cleaned.
Slowly move the tool back and forth over
the soiled surface. Release the spray trigger
to suction dirty water. Continue to clean
area, working in small sections, until dirt is
removed. Caution: Do Not Overwet.
10. When finished cleaning, remove and rinse
tool(s) in clean, running water.
11. It is recommended that you suction clean
water from a bowl to rinse out the hose.
12. Before wrapping hose onto tool rack, lift
end of hose and stretch out to ensure all
water is cleared from hose.
13. Wrap flex hose around tool rack.
14. Empty 2-in-1 water tank and rinse out,
following instructions in section C-4.
15. If the ReadyTools™ dial becomes difficult
to turn, the diverter assembly that holds the
dial may need to be cleaned. To clean, first
remove nozzle and locate screw that holds
the diverter assembly in place. With a Phillips
screwdriver, remove the screw and set aside.
16. Remove diverter assembly; hold under
running water making sure water flows
through and around the dial. Turn the dial
about 10 times clockwise and 10 more
times counter clockwise. This should free
up any debris.
17. Wipe diverter assembly with a soft cloth
and replace back on machine. Replace
nozzle.
18. Return ReadyTools™ dial to FLOOR
CLEANING setting.

IMPORTANT

Check for colourfastness in an inconspicuous place. If possible,
check upholstery stuffing. Coloured stuffing may bleed
through fabric when it becomes wet.