Maintenance And Inspection; Tool Change - MSW Motor Technics STYRO CUTTER 05 Manuel D'utilisation

VI. SCOPE OF APPLICATION
Cordless hot knife is designed for cutting elements made of expanded polystyrene (EPS), extruded
polystyrene (XPS), polyethylene, polypropylene and a large number of other foam materials used for
insulation of construction objects.
The user is liable for any damage resulting from non-intended use of the device!
VII. STRUCTURE OF THE MACHINE
G
E
B
C
F
VIII. TOOL CHANGE
a. Before first use.
Make sure the battery is properly installed in the device.
Make sure that the cutting tool is properly installed in the device.
b. Switching on and off
Switching on - press switch lock (C) and then press the switch (B)
Switching off - release the switch (B)
c. Installing the knife
Loosen the screws in the blade gripper (E) using the key provided. Then slide the knife blade
(holding the longer blade edge downwards) into the gap and tighten the screws.
Attention! Remove the battery from the device before installing the knife!
d. Removing the knife
To remove the knife from the device, loosen the screws using the key provided then pull out the
blade.
Attention! Remove the battery from the device before removing the tool and make sure that
the blade has cooled down! Risk of burns!
e. Cutting with the device
Before cutting set the temperature using the temperature adjustment knob (A). Check proper
functioning of the device prior to commencement of work. To do this, cut a discarded piece of
material. If fumes are generated during the operation it indicates that the pre-set temperature
is too high or the cutting speed is too low. Readjust the blade temperature and/or the cutting
speed. The knife will heat up to the pre-set temperature in a matter of seconds. To ensure
the maximum service life of the knife always use it within the given parameters and at proper
temperature.
Always follow the guidelines on work cycles when working with the device, i.e. 15 seconds of
continuous operation and 45 seconds of pause per each minute.
Attention! When cutting different types of plastic materials, always review manufacturer's specifications
concerning the material's softening, melting or degradation temperature!
12
A. temperature adjustment knob
A
B. switch
C. switch lock
D. battery locking switch
E. blade gripper
F. battery
D
G. operation indicator lamp
Rev. 13.10.2016
IX. MAINTENANCE AND INSPECTION
1. Inspecting the tool.
Clean the blade on regular basis and when accessories are burnt replace them with new accessories
since using contaminated and/or burnt blades will cause malfunction of the device.
2. Inspecting the mounting screws.
Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure to do so could result in serious hazard.
3. Cleaning the device.
To keep the device clean, clean it using a soft cloth damped in water with soap. Never use brushes
or other cleaning tools that may scratch/damage the device. Remember to prevent water from
penetrating inside the device through vents in the housing of the device. Clean the vents with a
paintbrush and compressed air. Contaminated blade must be cleaned when it has cooled down, using
the brush provided with the device.
X. TRANSPORTATION AND STORAGE
During transport, the machine should be protected from shaking and falling. Store the machine in a well
ventilated place with dry air and without corrosive gases.
XI. REGULAR CONTROL OF DEVICE
Regularly check the machine for signs of damage. If it should be damaged, please stop using it immediately
and contact your customer service to solve the problem.
What to do in case of a problem?
Please contact your customer service and prepare following information:
• Invoice number and serial number (the latter is to be found on the technical plate on the machine).
• If relevant, a picture of the damaged, broken or defective part.
• It will be easier for your customer service clerk to determine the source of the problem if you
give a detailed and precise description of the matter. The more detailed your information, the better
customer service will be able to solve your problem rapidly and efficiently!
CAUTION: Never open the machine without the authorization of your customer service. This can lead
to a loss of warranty!
Rev. 13.10.2016
13