Lenmar PPUKSALL Mode D'emploi

Model: PPUKSALL
Kickstand Battery 2.0
For iPhone® & iPod®
PLEASE READ THIS INFORMATION THOROUGHLY BEFORE USING THIS PRODUCT. IT CONTAINS IMPORTANT
OPERATING INSTRUCTIONS FOR YOUR UNIT.
Owner's manual
Thank you for purchasing the Kickstand Battery 2.0. The Kickstand Battery 2.0 o ers the convenience of an
external battery built into a portable iPhone/iPod kickstand.
You can use it at your desk as a Kickstand with the ability to charge your iPhone/iPod whenever you like or fold
it up and take it with you and still enjoy the bene t of extra battery power when you need it.
Included in the package you have purchased:
Kickstand Battery 2.0, USB charging / Sync cable and Owner's manual.
Charging your Kickstand Battery 2.0
Note: Prior to initial use fully charge your Kickstand Battery 2.0 before
connecting to your iPhone/iPod.
You can charge the Kickstand Battery 2.0 with the Micro USB to USB
cable included with the Kickstand Battery 2.0. Plug the Micro USB into
the Kickstand Battery 2.0's micro USB port, and the other end into a
computer's USB port or into a wall plug style adapter that has a USB port.
The LED status indicators show the current charging status of the case.
From left to right, the LEDs will blink and become steady as the
Kickstand Battery 2.0 charges. Once the 4th LED has become steady, the
charging process has nished.
If the Kickstand Battery 2.0 is connected to the iPhone/iPod and also
plugged into a USB port, charging is as follows:
First the iPhone/iPod will receive about 3 hours of charge and then the
Kickstand Battery 2.0 will charge for about 4 hours until full.
On/O Button
With the built in "ON / OFF" button you have the option of using the
Kickstand Battery 2.0 when you need it. When you need an extra charge
in your phone just push the ON/OFF button and hold for two seconds to
turn on and the Kickstand Battery 2.0 will proceed to charge your
iPhone/iPod's main battery. When you are ready to turn it o just hold
the button again for two seconds and the Kickstand Battery 2.0 will shut o .
Installing your iPhone/iPod into the Kickstand Battery 2.0
With your iPhone/iPod facing you, slide your iPhone/iPod into the
Kickstand Battery 2.0 from the top making sure the 30 pin connector and
the bottom of the iPhone/iPod line up and connect correctly.
Once in place you can push the ON / OFF button located on the back of
the Kickstand Battery 2.0 once, turning it on. You should now see the
charge indicator icon appear on your iPhone/iPod.
USB
MICRO USB
PORT
LED STATUS
INDICATOR
1st 2nd 3rd 4th
APPLE 30 PIN
CONNECTOR
MICRO USB
PORT
ON/OFF
BUTTON
Battery Consumption
Your Kickstand Battery 2.0 will always drain rst until its remaining power is at 5%; then your iPhone/iPod
switches to its main battery.
Checking remaining capacity of the case
The integrated LED status indicator shows how much battery power is left in your
case. Simply press the ON / OFF button. The 1st LED will indicate between 20 - 40%
charge remaining, the 2nd LED will indicate between 40 – 60% charge remaining,
the 3rd LED will indicate 60 - 80% charge remaining, and the 4th LED will indicate
80 -100% charge remaining.
SYNC
Enjoy the convenience of syncing your iPhone/iPod without ever
removing the Kickstand Battery 2.0. Using the supplied Micro USB cable
you can charge and sync your iPhone/iPod to iTunes® without ever
removing it. Just plug the Micro USB cable into the Kickstand Battery 2.0
and the other end into your computers USB slot.
Speci cations
Cell type: Lithium-Polymer Battery
Input: DC 5V, 500mA
Output: DC 5V, 1A
Capacity: 2000mAh
Dimensions: L90 x W57 x T11mm
Weight: 70g
Compatibility: iPhone 2G/3G/3GS/4 and most iPods
Standby: Up to 350 hours*
Talk Time: Up to 7 hours and on the 3G network, up to 14 hours on the 2G Network.
Internet Use: Up to 6 hours and on the 3G network, up to 10 hours on Wi-Fi
Audio Play: Up to 45 hours*
Video Play: Up to 10 hours*
*All above times may vary due to device settings, location, and signal strength
Limited 1 Year Warranty
Lenmar product is warranted to be free of defective parts and workmanship for stated period from the original date of purchase. Warranties are not transferable.
The warranty excludes damage resulting from accident, misuse, modi cation, delay or loss of use, damage to equipment or by normal wear and tear.
ALL WARRANTY REQUESTS MUST BE SUBMITTED AT: www.lenmar.com/warranty
INCLUDE A COPY OF ORIGINAL PROOF OF PURCHASE WITH RETURNED BATTERY OR THE CLAIM WILL BE DENIED.
Copy of Proof of Purchase from an authorized Lenmar Dealer must include the following:
- The company where the product was purchased
- The date of purchase
- The model number of the product purchased
- Send back the product freight prepaid (we recommend insuring the package as Lenmar will not be responsible for shipments lost or damaged in transit).
Include $10.00 payable to Lenmar Battery Solutions for processing fee for ship to address in the Continental United States.
Include $15.00 for ship to address in Hawaii, Alaska or Canada.
Use preprinted Lenmar shipping label or clearly print your RA Number on the outside of the shipping carton.
Proposition 65 Notice (California)
The following statement is required in the state of California pursuant to the settlement of an action brought by the Mateel Environmental Justice Foundation against
multiple electronics and appliance manufacturers
• WARNING: Handling the cord on this product will expose you to lead, a chemical known to the state of California to cause birth defects or
other reproductive harm. Wash hands after handling.
For additional questions, comments or to explore other Lenmar battery solutions, visit our web site at: www.lenmar.com or call 800/424-2703 from 9AM – 5PM PST.
Lithium-Polymer battery must be
recycled or disposed of properly.
311-321-33-0629 r1 y1
Send to:
Lenmar Battery Solutions
Attn: Return Department
4035 Via Pescador
Camarillo, CA 93012-5050
LED STATUS
INDICATOR