Technical Specifications - MSW Motor Technics BLS-100 Manuel D'utilisation

OPERATION MANUAL
SYMBOLS
Symbols on the name plate indicate important product and operational information.
Operation manual must be carefully read.
Never dispose of electrical equipment together with household waste.
This device is conform with CE declarations.
PLEASE Drawings in this manual are for illustration purposes only and in some details may differ from the
actual device.
NOTE!
I. GENERAL OPERATIONAL PRECAUTIONS
1. Keep work area clean. Cluttered areas can cause injuries.
2. Consider work area environment. Don't expose power tools to rain or wet soil. Don't use power tools in damp or
wet locations. Work area should be well protected. Don't use tool in presence of flammable liquids or gases. Power
tools produce sparks during normal operation or when switching ON/OFF. Never use power tools in dangerous sites
containing lacquer, paint, benzene, thinner, gasoline, gases, adhesive agents, and other materials which are combustible
or explosive.
3. Provide sufficient protection against electric shock. Prevent body contact with grounded surfaces. For example: pipes,
radiators, ranges, refrigerator enclosures.
4. Keep children and third parties away from work area.
5. Store unused tools. When not in use, tools should be stored in dry and high or locked-up place out of reach for
children.
6. Do not overload the machine! To ensure an optimum in the performance and safety of the device, only use within
the set parameters.
7. Use only suitable tools. Don't use small tools or attachments. Don't use tool for not intended purposes. For example:
don't use circular saw for cutting tree limbs or logs.
8. Dress properly. Do not wear loose clothing or jewellery. They can get caught in moving parts. Rubber gloves and
non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair.
9. Use safety glasses. Also use face or dust mask if cutting operation is dusty.
10. Do not damage the connection cable. Never carry tool by cord or yank it to disconnect from the plug. Keep cord
from heat and oil sources and sharp edges.
11. Secure work area. It is recommended to use clamps or a vice for fixation. Please pay special attention to your hands
when operating the device!
12. Do not overreach yourself. Keep proper footing and balance at all times.
13. Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubri-
cating and changing accessories. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean,
and free from oil and grease.
14. Switch off the device and disconnect the cable before maintenance or changing accessories e.g. blades, bits, cutters.
15. Remove adjusting keys and wrenches. Always make sure that keys and adjusting wrenches are removed from tool
before turning it on.
16. Avoid unintentional starting. Don't carry plugged-in tool with finger on switch. Be sure switch is off when plugging in.
17. During outdoor work use extension cords intended for outdoor use and marked accordingly.
18. Stay alert when operating the device. Do not operate tool when you are tired.
19. Check damaged parts. Before further use of the tool, any covers or other parts that are damaged should be carefully
checked to determine that it will operate properly and perform its intended function. Check for alignment of mo-
ving parts, mounting, and any other conditions that may affect its operation. A cover or other part that is damaged
should be properly repaired or replaced by an authorized service centre unless otherwise indicated elsewhere in this
instruction manual. Defective switches should be replaced by an authorized service centre. Do not use tool if switch
does not turn it on and off.
20. Do not use power tools for applications other than those specified in the instruction (other than that for which it
was designed).
21. To ensure the designed operational integrity of power tools, do not remove installed covers or screws.
22. Do not touch movable parts or accessories unless the power source has been disconnected.
23. Use your tool at lower input load than specified on the nameplate to increase working efficiency and decrease wear
out.
Rev. VIII 2017
8
24. Do not wipe plastic parts with solvent. Solvents such as gasoline, thinner, benzene, alcohol, ammonia and oil may
damage and crack plastic parts. Do not wipe them with such solvents. Wipe plastic parts with a soft cloth lightly
dampened with soapy water.
25. Consult an authorized service agent in the event of power tool failure.
26. Use only original replacement parts.
27. This tool should only be disassembled for replacement of carbon brushes.
II. PRECAUTIONS ON USING THE DEVICE
1. Wear protective glasses to protect your eyes.
2. Use earplugs to keep your ears noise-free while working.
3. Properly set the bit holder.
4. The tool becomes very hot during operation.
5. Be sure to use side handle.
6. Safe operation depends on one's work posture.
7. When working at a highly elevated location, pay attention to objects and persons below.
8. Wear protective shoes to protect your feet. Wear protective gloves.
9. To avoid injury from accidental starting, always remove the plug from the electrical socket before installing or remo-
ving a cutting knife.
III. TECHNICAL SPECIFICATIONS
Device
Rated voltage/frequency
Rated power
Rotational speed, no load
Cutting thickness
Steel metal sheet:
Stainless steel metal sheet:
Other metals (aluminium, copper)
Plastics
Min cutting diameter
Sound power level L
wA
Uncertainty K
Sound pressure level L
pA
Uncertainty K
Vibration emission value a
h
Uncertainty K
Sound level for the operator may exceed 85 dB (A). Wear hearing protection!
IV. DEVICE DESIGN AND CONSTRUCTION
8
8
9
9
7 7
10
6
6
8
5
5
6095 BLS-100 6096 BLS-300
230 V / 50 Hz
625 W
1,000 rpm
2,3 mm 4 mm
1,6 mm 2,5 mm
2,5 mm 4 mm
2,5 mm 4 mm
250 mm 300 mm
90.9 [dB(A)]
3 [dB(A)]
79.9 [dB(A)]
3 [dB(A)]
1.77 m/s 2
1.5 m/s 2
10
4
3
8
11
2
1
Rev. VIII 2017
9