Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
M1.1.WEL33.NLFREN - 25042019
EN
•
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
•
Children should be supervised to ensure that they do not play with the appliance.
2 Introduction
•
Depending on the power cord type this fan heater may be used only in household, warehouses and workshops, building
sites or greenhouses depending. It incorporates a thermostat and a self-resetting thermal cut-out to control the heating
elements. The thermostat feels the air temperature and controls the surrounding temperature. The fan motor is controlled by
thermostat and it stops working when the thermostat cuts off the heating element, and the self-resetting thermal cut-out will
switch off the heater to ensure the safety when overheating.
•
When using the heater for the first time, you may notice a slight emission of smoke. This is quite normal and it stops after
a short time. The heating element is made of stainless steel and was coated with protection oil by production. The smoke is
caused by the left oil when heated.
3 Technical specifications
Model
Waterproof class
Voltage
Required power
Current
Required fuse
Setting
Self-resetting thermostat
Product dimensions
Net weight
•
Housing of steel plate and coated by heat-resistant powder.
•
Supplied complete with cord and plug.
4 Description of control panel
•
Left knob: Selector with heat setting
•
Right knob: Thermostat dial
5 Using instructions
1. Position the fan heater so that it stands upright on a firm surface and at a safe distance from wet environments and
flammable objects.
2. Connect the fan heater to the mains.
3. Set the thermostat knob to the MAX and let the heater operate with full power.
4. The fan heater will switch on when the heating selector is set to one of the power settings.
5. Once the room reaches the required temperature, heating element will stop working, fan keep working. Once the
temperature decreased, the heating element will be working. The fan heater now starts and stops automatically and thus
keeps the room temperature constant.
6. Before switch off the heater, please turn the thermostat to MIN position and turn the switch to fan position, let the appliance
cool down for two minutes then turn off the heater and pull out the plug.
WEL33
IPX4
220 - 240 V
3000 W
12.5 - 13.6 A
15 A
25 / 1500 / 3000 W
65 °C
270 x 255 x 400 mm
4.6 kg
surrounding temperature
working when the thermostat cuts off the h
And The self-resetting thermal cut-out will sw
safety when overheating.
2.2 When using the heater for the first time
smoke. This is quite normal and it stops afte
made of stainless steel and was coated with
smoke is caused by the left oil when heated
3. Technical specifications
Model
Waterproof Class
Voltage
required power
current
Required Fuse
Setting
Self-resetting Thermostat
Product Meas (
N.W.( KG)
3.1 Housing of steel plate and coated by hea
3.2 Supplied complete with cord and plug
4.
Description of Control Panel
4.1 Left Knob : selector with heat setting
4.2 Right Knob : Thermostat dial
5. Special safety regulations
5.1 Before use, please check the marking on
power cord type this appliance may be used
Type
H07RN-F
9
. The fan motor is
25/1500/300
mm)
You can use the appliance
household, warehouses a
workshops, building sites
IFH01-33H-
IPX4
220-240V
3000W
12.5-13.6A
15A
65°C
270*255*40
4.6
2
Publicité
Table des Matières
