EINHELL TP-AP 18/28 Li BL Instructions D'origine page 17

If this fails to happen, try turning the ring (a) by
hand into its starting position.
Pull on the blade to check whether it sits tightly in
the holder.
5.2 Adjusting the soleplate (Fig. 3)
Warning!
Pull out the battery pack.
To adjust the soleplate, press the soleplate lo-
cking button (5) on the right-hand side (looking
from the bottom) in order to unlock the soleplate
(3). Set the required distance and press the so-
leplate locking button (5) on the left-hand side
(looking from the bottom) in order to lock the sole-
plate again. Check that the soleplate is secure.
5.3 Charging the Li battery pack (Fig. 4-5)
1. Remove the battery pack (d) from the handle,
pressing the pushlock button (c) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(e) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
Anl_TP_AP_18_28_Li_BL_Solo_SPK13.indb 17 Anl_TP_AP_18_28_Li_BL_Solo_SPK13.indb 17
GB
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.4 Battery capacity indicator (Fig. 4 /Item f)
Press the button for the battery capacity indicator
(g). The battery capacity indicator (f) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
6.1 On/Off switch (Fig. 1/Item 1)
To switch on:
Press the locking button (2) and the On/Off switch
(1).
Infi nitely variable stroke speed control is possible
with the On/Off switch (1). The further you push
the switch, the higher the stroke speed.
To switch off :
Release the locking button (2) and the ON/OFF
switch (1) at the same time
6.2 Use as a jigsaw (Fig. 6)
Place the multi-saw on the material to be cut as
shown in Fig. 6. Switch on the multi-saw and push
it along against the material to be cut. Adapt your
cutting speed to the material.
- 17 -
27.07.2021 07:39:27 27.07.2021 07:39:27