Technical Data; Before Starting The Equipment - EINHELL TP-AP 18/28 Li BL Instructions D'origine

4. Technical data

Motor power supply: ............................... 18 V DC
Stroke speed: ...................................0-2500 min
Stroke height: ........................................... 28 mm
Cutting depth, wood: .............................. 200 mm
Cutting depth, iron: ................................... 12 mm
Cutting depth for plastic ........................... 20 mm
Maximum saw blade width: .............. 0.9 -1.6 mm
Weight: .......................................................1.9 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ..................... 82.9 dB(A)
pA
K uncertainty ............................................. 5 dB
pA
L sound power level ....................... 93.9 dB(A)
WA
K uncertainty ............................................. 5 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Cutting wooden boards (front handle)
Vibration emission value a
Uncertainty K = 1.5 m/s
Cutting wooden boards (rear handle)
Vibration emission value a
Uncertainty K = 1.5 m/s
Cutting wooden beams (front handle)
Vibration emission value a
Uncertainty K = 1.5 m/s
Cutting wooden beams (rear handle)
Vibration emission value a
Uncertainty K = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
Anl_TP_AP_18_28_Li_BL_Solo_SPK13.indb 16 Anl_TP_AP_18_28_Li_BL_Solo_SPK13.indb 16
GB
-1
= 13.23 m/s²
h
2
= 11.01 m/s
2
h
2
= 11.30 m/s
2
h
2
= 10.31 m/s
2
h
2
- 16 -
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Changing the saw blade (Fig. 2)
Warning!
Switch off the universal saw and pull out the bat-
tery pack each time before doing any work on the
machine and changing the blade.
Turn the ring (a) on the blade holder (4) as shown
in Fig. 2 until the blade (b) lets itself be slipped
into the slot of the blade holder (4).
When you now let go of the ring (a) again, the ring
(a) should return to its starting position.
27.07.2021 07:39:27 27.07.2021 07:39:27