Hughes JVC G1000S Manuel D'instructions page 46

Operating the Main Menu (Cont.)
Setting and Adjusting Other Functions (OPTIONS) (Cont.)
Remote control unit
OPERATE
VOL.
PAGE
BACK
PRESET
QUICK
ALIGN.
PAGE BACK button
Submenu items
[OPTIONS menu]
M E N U A U T O O F F
L I N E D I S P L A Y
R I G H T L E F T R E V .
T O P B O T T O M I N V .
C L A M P
R E S I Z E
B A C K C O L O R
C O L O R T E M P .
A S P E C T C H A N G E
S L E E P T I M E
L A M P T I M E
Notes
• The selected item is shown in magenta color. Items shown
in gray color cannot be operated or set in the current mode.
• Items to be set (adjusted) are different when AV signals are
input and when computer-system signals are input.
• When you turn the RESIZE function ON, allowing the screen
to be enlarged virtually to its full size for projection (resizing
display), the video image (resolution) becomes coarse.
44
G1000S 34-45.EN
MENU/ENTER
button
COMPUTER VIDEO
FOCUS
MENU/ENTER
Cursor buttons
AV
MUTING
O P T I O N S
N O
O N
O F F
O F F
B P
O N
B L U E
M I D D L E
4 : 3
3 0 M i n .
1 0 H .
44
5 Set (adjust) the desired item with the
cursor button 2 or 3.
• To adjust multiple items, repeat steps 4 and 5.
Adjustment item Button
Sets whether to clear the menu display
automatically a fixed time later or not.
(Factory setting : NO)
MENU AUTO
YES: Clears the display automatically in
2/3
OFF
NO : Does not clear the display
NO
Sets whether to show the line display (Y/C,
VIDEO, etc.) at the top of the projected
screen or not. (Factory setting : ON)
OFF: Does not show the line display.
2/3
LINE DISPLAY
ON : Shows the line display.
OFF
Reverses video image right-to-left.
(Factory setting : OFF)
RIGHT LEFT
2/3
OFF: For the front method
REV.
ON : For upside hanging from the ceiling
OFF
Inverses video image upside-down. (Factory
setting : OFF)
TOP BOTTOM 2/3
OFF: For normal set-up
INV.
ON : For upside hanging from the ceiling
OFF
Sets the clamp pulse's position at the back
porch (BP) or on the sink tip (ST).
Normally, the clamp is used at BP. If, with
some PCs or workstations, the screen
becomes unstable such as being too dark
or too bright, try to switch to ST.
2/3
CLAMP
(factory setting: BP)
BP : The clamp pulse is positioned at the
ST : The clamp pulse is positioned on the
BP
When the number of pixels (resolution)
sought by the input video is smaller than that
(resolution) of D-ILA device, the video image
is then enlarged to virtually full screen size
of D-ILA device and projected (resizing
display). (Factory setting : ON) Does not work
(cannot be set) for video system input.
OFF : Does not enlarge the video image for
2/3
RESIZE
ON : Enlarges virtually to the full screen size
OFF
98.9.21, 9:56 AM
Adjustment content
about 25 seconds.
automatically.
YES
(The line display disappears about 5
seconds after it is shown.)
ON
ON
ON
back porch.
sink tip.
ST
projection. When the number of pixels
sought by video image is smaller than
that of D-ILA device, projection takes
place on a small screen size with a
black area around the screen.
of D-ILA device for projection (resizing
display).
ON
(To be continued on the next page)