Feit Electric 74050 Instructions page 2

LED FLAT PANEL FIXTURE INSTRUCTIONS
3. Now as you raise the lamp unit up into the Mounting Bracket, Push/feed the electrical wire up into the junction box.
a) Match up alignment arrows (1-1) indicated on the
Mounting Bracket and the lamp Unit
1
IMPORTANT SAFETY INFORMATION
1. WARNING: RISK OF SHOCK House electric current
can cause painful shock or serious injury unless
handled properly. For your safety, always remember to:
A. Turn off the power Supply at the fuse or circuit
breaker box before you install the fixture.
B. Ground the fixture to avoid potential electric shocks
and to ensure reliable starting.
C. Double-check all connections to be sure they are
tight and correct.
D. Wear rubber soled shoes and work on a sturdy
wooden ladder.
CAUTION
WARNING: Risk of fire. Use only on 120 volt 60Hz circuits. Suitable for damp locations. Before installing your lighting fixture,
thoroughly review enclosed installation manual. If you do not have sufficient electrical wiring experience, please refer to a
do-it-yourself wiring handbook or have your fixture installed by a qualified licensed electrician. All electrical connections
must be in accordance with Local and National Electrical Code (NEC) Standards. Reliable operating temperature is 0˚F
–120˚F. If flickering occurs in low level dimming, increase light level. Compatible with most dimmers including Leviton
6681-IW, Lutron S-600P and Lutron DVCL-153. Dimmable to 10% with most dimmers. For more information including
dimmer compatibility visit www.feit.com or call our toll free number 1-866-326-BULB.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
FEIT ELECTRIC COMPANY | PICO RIVERA, CA | (800) 543-3348 | FAX (562) 908-6360 | www.feit.com
b) Twist and lock the lamp Unit into the mounting
bracket in the "Lock direction to match up alignment
arrows (1-2)
WARNING!! IF NOT LOCKED IN PLACE THE
FIXTURES MAY FALL AND CAUSE SERIOUS
INJURY!!
2. This fixture is designed for use in a circuit protected
by a fuse or circuit breaker. It is also designed to
be installed in accordance with local electrical codes.
If you are unsure about your wiring, consult a qualified
electrician or local electrical inspector, and check your
local electrical code.
3. WARNING: RISK OF CUTS Some metal parts in the
fixture may have sharp edges. To prevent cuts and
scrapes, wear gloves when handling the parts.
4. Account for small parts and destroy packing material,
as these may be hazardous to children.
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures: Reorient or relocate the
receiving antenna. Increase the separation between the
equipment and receiver. Connect the equipment into an
outlet on a circuit different from that to which the receiver
is connected. Consult the dealer or an experienced radio/TV
technician for help.
c) Once locked in place remove the stickers and gently
align the lamp unit and mounting Bracket for best fit.
LIMITED WARRANTY
This product is warranted to be free from
defects in workmanship and materials for up
to 5 years from date of purchase. If it fails to
do so, please contact Feit Electric at info@
feit.com or call 1-866 326-BULB (2852) for
instructions on replacement. Do not return
the product to the store.
For comments please write to:
FEIT ELECTRIC
Customer Service Department
4901 Gregg Road, Pico Rivera, CA 90660
SAVE THESE INSTRUCTIONS.