babymoov DIGITAL Notice D'utilisation page 10

- The two time figures in the clock display area will flash and show the figures "12".
- Start setting the hour by pressing the "+" or "-" button. The setting range is from 0 to 23 hours and each push on the button
represents one hour. If it is one in the morning, the screen will display "1:00" instead of "01:00" (note: when you press the
"+" or "-" button and keep it pressed down, the hours - from 0 to 23 hours – will automatically increase or decrease).
- If the number reaches "23", when you press the "+" button, it becomes "00".
- When you have finished setting the hour, press the button
the minutes.
Note:
if you have not pressed the button
will not be implemented or recognized. The clock on the screen will return to its initial setting and will indicate "12:00".
- In the minute setting mode, the two minute figures in the clock display area will flash and show the figures "00".
- Start setting the minutes by pressing the "+" or "-" button. The setting range is from 0 to 59 minutes and every push of
the button represents one minute (note: when you press the "+" or "-" button and maintain the pressure, the minutes -
from 1 to 59 – will automatically increase or decrease). If the screen displays "59", when you press "+", the screen will
display "00". If the screen shows "00", when you press "-", the screen will display "59".
- Once the minute setting is complete, press the button
Note:
if you haven't pressed the button
not been completed, the minute display returns to "00".
Room temperature display
The humidifier will detect the room temperature and will display it on the LCD screen.
Hygrometer display
The humidity sensor detects humidity in the room and displays the humidity level (% humidity) on the hygrometer display
(detection range: 30 to 90 % humidity).
Setting the desired humidity level (hygrometry)
- Press the button twice, the programme will enter the desired humidity level setting. The figures "90" will flash and will
be displayed in the clock area of the LCD screen
- The initial humidity level setting is 90 %. Presss the "+" or "-" button to set the desired humidity level. The setting unit is 5 %
each time you press. The humidity level setting range is from 30 % to 90 % (please note that the ideal humidity level in a
bedroom is around 40 to 50%).
- When the setting is complete, press the button
complete, the icon
continue to flash for 45 seconds, and will return to the initial setting). You can check the desired humidity level by pressing
the button once. The desired setting will then appear on the screen for 3 seconds, after which the previous screen
display will reappear.
- The humidity sensor will detect the humidity level in the room. The programme will automatically detect variations in the
humidity level and will set the desired level.
- Cancelling the humidity level setting: press the button
the humidity level setting, the humidification function is no longer active).
Setting the timer
- Press the button twice, the programme will enter the timer programming mode. The clock screen will flash and display "12.00".
- Press the "+" or "-" button to set the desired countdown for the start of vaporisation.
- Each setting unit is 30 minutes and the setting is only valid for minutes. For example, when the screen indicates 12:30,
press the "+" button once, the screen will change to 13:00 (note: when you press the "+" or "-" button and maintain the
pressure, the minutes increase or decrease automatically). Please note that each stage is 30 minutes.
- When the setting is complete, press once on the button
Note:
if you have not pressed the button
complete or recognised in this case.
When you have set the timer, be careful to ensure that you have set the desired humidity level (cf.above "Setting the desired
humidity level (hygrometry) ".
- Setting the time is shown in the form of a countdown. When the countdown is complete, the icon
LCD screen and humidification will begin.
- You can check the countdown setting by pressing the button
before the humidifier begins to work. Flashing of the countdown display will last for 3 seconds and will then return to the
previous display mode. For example, you set the timer to 5:00 (you therefore wish vaporisation to start in 5 hours). When
you go to the timer setting mode after 25 minutes, the display will indicate 04:35.
10
to confirm, the adjusted clock will continue to flash for 45 seconds. The hour setting
to confirm, the adjusted clock will continue to flash for 45 seconds. If the setting has
lights up on the LCD screen (note: if you have not pressed the button
to confirm, the time setting will continue to flash for 40 seconds. The setting is not
DIGITAL HUMIDIFIER • Instruction Manual
once to confirm that the setting is complete and go on to set
once to confirm that the minute programming setting is complete.
once to confirm the setting. When the setting of the programme is
for 5 seconds, the setting will be cancelled (note: if you cancel
to confirm the setting. The icon
once. The display will indicate the time that remains
to confirm, the setting will
illuminates on the LCD screen.
will go out on the