Storing The String Trimmer; Troubleshooting - Sabo ST-30 Mode D'emploi

REPLACING THE CUTTING LINE
See figure 10 to 12
·
Remove the spool (21) from the trimmer head housing (24).
NOTE
Remove any old cutting line that may still be on the spool.
NOTE
Use only nylon cutting line with a diameter of 1.65 mm.
IMPORTANT
You must mount the cut-off blade (8) if you are using the trimmer head (10).
·
Cut two cutting lines with an approximate length of 3 m.
·
Bend one end of the cutting line 6.35 mm (1/4").
· Insert one end of the cutting line into one of the spool anchor holes (25).
·
Wrap the cutting lines with your finger evenly and firmly between the cutting lines in the specified direction around the spool. Do not wind the cutting line beyond the outer ribs of
the spool.
·
After the last turn, place one cutting line in each of the line slots (26) on the opposite side.

11 STORING THE STRING TRIMMER

· Remove the battery from the trimmer before storing the string trimmer.
·
Store it in a location out of the reach of children.
·
Keep the battery away from the corrosives such as garden chemicals and salt.
·
Keep an unused battery away from paperclips, coins, keys, screws, nails and all other objects that could connect the contacts.
·
A short circuit of the battery can cause burns or fires. Store the battery in a dry place and at a temperature below 27°C.
·
Never store discharged batteries. A battery that is too warm must be allowed to cool before charging.
·
The battery's charge will diminish during storage. The higher the temperature, the faster the discharge. Recharge the batteries monthly if they are being stored for a longer period.
This increases the life and maintains performance.
·
Remove the battery from the device before adjusting settings, replacing accessories or after use. This prevents the risk of your device being switched on inadvertently or unsupervised.
·
Secure the string trimmer during transport in order to prevent damage and injuries. Clean the device before storage.
ENVIRONMENTAL PROTECTION
·
Environmental protection should be an essential and prioritised aspect when using the machine. Do not disturb your surroundings when using the device.
·
Strictly observe the local provisions for disposal of the packaging, oil, petrol, filters, damaged parts or all other polluting materials. These materials must not be disposed of with
domestic waste, but instead must be collected separately and disposed of at a recycling site that recycles the materials.
·
Strictly observe the local provisions for disposal of the cut waste.
The device must not be disposed of in the regular waste, but instead must be disposed of at a recycling site according to the local provisions.

12 TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES
There is no electrical contact
between the machine and the
The machine does
battery.
not start when you
The battery is empty.
press the switch
The safety lock button (2) and the
trigger (1).
switch trigger (1) are not pressed
in sequence.
The grass deflector (11) is not
mounted to the machine.
Heavy cutting line is used.
Grass winds around the motor
shaft and the trimmer head.
The machine
stops when you
cut.
The motor is overloaded.
The battery or the machine is too
hot.
SOLUTION
·
Remove the battery.
·
Check the contact.
·
Re-insert the battery.
Charge the battery.
·
Press the safety lock (2) on the battery and hold it down.
· Push the switch trigger (1) to start the machine.
·
Remove the battery.
·
Attach the grass deflector to the machine.
Use only nylon cutting line with a diameter of 1.65 mm.
·
Stop the machine.
·
Remove the battery.
·
Carefully remove the grass from the motor shaft and/or the trimmer head.
·
Free the trimmer head from the grass. See the section "If grass wraps around the trimmer head or the shaft
housing" in these operating instructions.
·
You can continue using the motor when the load has been removed.
·
As you are cutting, move the trimmer head into and out of the grass you want to cut and do not cut more than 20 cm in
a pass.
·
Let the battery cool until its temperature is reduced.
·
Let the machine cool for approx. 10 minutes.
35