Publicité
Les langues disponibles
Les langues disponibles
Digital Indoor Antenna
Item no. 94 06 66
1.
Intended use
The "digital indoor antenna" amplifies received signals from terrestrial digital video broadcaster and offers
the best reception available. It can also be used as a photo frame. Only operate this appliance with adaptor
provided. The product should only be used in dry indoor areas.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
2.
Delivery content
•
Digital indoor antenna
•
Power adaptor
•
Operating instructions
3.
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
Persons / Product
•
The device is not a toy. Keep it out of the reach of children and pets.
•
Do not leave packaging material lying around carelessly. These may become dangerous playing material
for children.
•
Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture,
flammable gases, vapours and solvents.
•
Do not place the product under any mechanical stress.
•
If it is no longer possible to operate the product safely, take it out of operation and protect it from any
accidental use. Safe operation can no longer be guaranteed if the product:
-
is visibly damaged,
-
is no longer working properly,
-
has been stored for extended periods in poor ambient conditions or
-
has been subjected to any serious transport-related stresses.
•
Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the
product.
•
Also observe the safety and operating instructions of any other devices which are connected to the
product.
•
Never touch the mains plug when your hands are wet.
•
Never pull the power cord to withdraw the adaptor from socket. Always use the grip areas provided.
Miscellaneous
•
Consult an expert when in doubt about operation, safety or connection of the device.
•
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified
shop.
•
If you have questions which remain unanswered by these operating instructions, contact our technical
support service or other technical personnel.
4.
Installation
Place the antenna safely on a level and sturdy surface, otherwise it may fall down and
injure people.
Do not drill any additional holes or screw any additional screws into the housing to mount
the antenna.
Pay attention when mounting on a wall that no power, gas or water pipes are damaged
by mistake!
When mounting on a wall, use screws and wall plugs, which are compatible with the
composition of the wall
1.
Attach the standing unit to the main unit.
2.
Insert the coax plug into appropriate aerial jack in your set top box (STB), and F-type connector screw-on
plug into the F-type jack in the antenna.
3.
Connect the DC plug of the adaptor to the DC socket in the back of antenna and the AC plug to the mains.
4.
Place the antenna near the STB or television and alter its position or orientation (horizontal or vertical) to
obtain the best possible reception.
5.
Rotate the stand clockwise or anticlockwise to change the antenna orientation, horizontal or vertical.
6.
If the reception is still not satisfying, please try wall-mounted installation.
Wall mounting
1.
Connect the coaxial cable and the adaptor as mentioned above. Move the antenna along the wall to search
for the position with best reception.
2.
Detach the main unit and use the standing unit as a template to mark positions on the wall for two screw
holes. Use a spirit level to achieve horizontal alignment for the holes.
3.
For wooden wall, choose two suitable wood screws.
4.
For brick or reinforce concrete wall, drill two 5.8 mm holes to 35 mm depth and insert 2 wall plugs or anchor
bushings.
5.
Screw the screw in but not completely, leave 15 mm between the bottom of screw cap and the wall. Thus
the antenna can be suspended correctly.
6.
Match the slots. Press the antenna against the wall and slide it down to ensure secure mounting.
Suggestions on how to obtain best reception:
•
Position the antenna far from any source of interference and near to the window.
•
Install the antenna as high as possible to reduce the chances of interference.
Different local stations with different transmission power are available depending on your location.
Reception can vary accordingly.
Version 06/11
As a photo frame:
You can slide a photo (10 x 15 cm) behind the plastic plate on the front.
5.
Maintenance
Before cleaning the appliance, always disconnect it from its power source.
Never repair any defective connection lines yourself. In such case, disconnect the
appliance from its power supply and send it to a specialised workshop.
The surface of the device should be cleaned with a soft and slightly damp cloth or dry brush. Do not use
aggressive cleaning agents or chemical solutions, which could damage the housing or impair its operation.
6.
Disposal
In order to preserve, protect and improve the quality of environment, protect human health and
utilise natural resources prudently and rationally, the user should return unserviceable product to
relevant facilities in accordance with statutory regulations.
The crossed-out wheeled bin indicates the product needs to be disposed separately and not as
municipal waste.
7.
Technical data
Digital indoor antenna
Operating voltage:
Frequency range:
Maximum amplification:
Impedance:
Output level:
Power adaptor
Input voltage:
Input current:
Output voltage:
Output current:
© 2011 by Conrad Electronic SE.
12 V/DC
47 – 230 MHz / 470 – 870 MHz
VHF (47 – 230 MHz) 20 dB
UHF (470 – 870 MHz) 20 dB
75 Ohms
- 6 dBm or 101 dBuV (maximum) at 620 MHz 1dBm compression
230 V/AC, 50 Hz
150 mA
12 V/DC
250 mA
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
All rights including translation reserved. Reproduction by any method, e.g.
photocopy, microfilming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
V2_0611_02-SB
Publicité
