Publicité
Les langues disponibles
Les langues disponibles
G
O P E R A T I N G I N S T R U C T I O N S
Mini Barcode Scanner, Wireless
Item no. 401264
Intended Use
The product is used for contact-free reading of barcodes. The data transfer to PC or mobile
device (e.g. iOS, Android) occurs via Bluetooth.
A built-in rechargeable battery is used to supply the power; this can be charged via USB.
Always observe the safety instructions and all other information included in these operating
instructions.
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Package Contents
• Barcode scanner
• USB cable
• Wrist strap
• CD with manufacturer's operating instructions in English
• Manufacturer's programming guide, with barcodes for programming (e.g. Bluetooth pairing)
• Quick guide
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any resulting
damage!
We shall not accept liability for damage to property or personal injury caused
by incorrect handling or non-compliance with the safety instructions! In such
cases, the warranty will be null and void.
• The unauthorised conversion and/or modification of the product is not permitted for
safety and approval reasons (CE). Never dismantle the product.
• The product is not a toy and should be kept out of the reach of children.
• The product is intended for use only in dry, indoor locations. The product must not
get damp or wet.
Protect the product from cold, heat, direct sunlight, dust and dirt.
• Never look into the light beam of the barcode scanner with the naked eye or with
optical instruments. There is risk of eye damage!
• Do not leave the packaging material carelessly lying around, since it could become
a dangerous plaything for children.
• Handle the product with care; it can be damaged by impacts, blows, or accidental
falls, even from a low height.
LED display and signal tones
• Next to the control key on the top, an LED gives information on the function of the barcode
scanner:
LED Display
Function
Off
Barcode scanner in standby mode or off
Flashes green
Not connected or reportable via Bluetooth search
Lights green 2 s
Barcode correctly recognized
Flashes red
Flat battery
Lights red
Battery is charging
• An integrated acoustic signaller gives the following information:
Signal tone
Function
1x long
Switch-on process
1x
Barcode correctly recognized
1x short
ASCII Code 39 recognized in configuration process
2x
Wireless connection established
2x short
Configuration barcode correctly recognized
3x
Wireless connection ended
3x short
Barcode read, although no wireless connection is active (or an incor-
rect barcode was scanned during the configuration mode)
5x
Rechargeable battery flat
8x short
The barcode scanner switches between the two transmission modes
(SPP/HID)
Getting Started
www.conrad.com
Version 01/15
• The rechargeable battery installed in the barcode scanner is usually flat on delivery. To
charge it, use the USB cable to connect the barcode scanner to a free USB port on your
computer, a USB hub with its own power supply or the USB port e.g. of an appropriate wall
plug transformer.
The charging time when the rechargeable battery is flat is about 2 hours.
• To switch on the barcode scanner, press the button on the top. The barcode scanner switches
off automatically after an adjustable time (you can set the desired time by scanning the
corresponding barcode in the manufacturer's programming guide; you can also deactivate
the automatic switch-off).
Pairing
• To start the pairing process, scan the "Disconnect" barcode on the enclosed manufacturer's
programming guide.
• If the barcode scanner is connected to an Android device, an iOS device or a PC, scan the
barcode „BT mode HID".
• On the device you use, carry out a search for available Bluetooth devices. The barcode
scanner should be found after a short time.
If the Bluetooth software device requires you to enter a PIN code on the barcode scanner,
scan the barcode "Pincode Start", then the barcodes for the required digits, then the "Enter"
barcode and finally the barcode "Pincode Stop".
Please consult the manufacturer's English programming guide.
Function of the barcode scanner
The barcode scanner functions in a manner similar to a Bluetooth keyboard. It transmits the
data contained in the scanned barcode as text to the receiver (e.g. a PC or a mobile device),
which then shows this information in the already running software (spreadsheet, text editor).
Maintenance and Cleaning
The product does not require any maintenance and should never be disassembled for any
reason.
Only use a clean, soft and dry cloth for cleaning. Do not use aggressive cleaning agents, as
these can cause discolouration.
Do not press too strongly on the surface when cleaning, to prevent scratch marks.
Dust can be easily removed with a soft, clean, long-haired brush and a vacuum cleaner.
Disposal
Declaration of Conformity (DOC)
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that
this product conforms to the fundamental requirements and the other relevant regulations of
the directive 1999/5/EC.
If the enclosed CD contains not only the manufacturer's instructions but also soft-
ware, the latter is not intended for the enclosed barcode scanner, but rather for
another model. Do not install the software.
Entering a PIN code (e.g. by scanning the barcode) during the pairing process
must occur within a set period of time. If the entry occurs too slowly, the barcode
scanner is not reported.
In that case, start the search for available Bluetooth devices again as described
above.
Electrical and electronic devices do not constitute household waste.
Dispose of an unserviceable product in accordance with the relevant statutory regu-
lations.
The Declaration of Conformity for this product can be found at www.conrad.com.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau
(www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited. This publication represent the technical status at the time of
printing.
© Copyright 2015 by Conrad Electronic SE.
Publicité
