Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 12
EN
Drilling wood
WARNING: The dust produced from working with some materials can be toxic. Beech, oak,
mahogany and teak natural woods, man-made composite woods and some surface treatments,
including paint with lead, are toxic. Lead-based paint is common in buildings built before 1960.
Always wear suitable respiratory protection; for example, a respirator face mask. Use a dust
extraction system or regularly vacuum the work area to prevent the build-up of dust. In addition,
vacuum the work area after the work has been completed. Most dust is a fire hazard. Overhead work
surfaces have an increased safety risk for dust.
• Select drill mode with the Torque Selector (3)
• Ensure the drill bits are suitable for wood and are within the maximum capacity of this power
tool (see 'Specification')
Drilling metal
• Select drill mode with the Torque Selector (3)
• Ensure that drill bits are suitable for the grade of metal being drilled and are within the
maximum capacity of the tool (see 'Specification')
• To ensure accuracy, mark the intended hole position using a hammer and centre punch
WARNING: The drill bit and the workpiece will become very hot when drilling metal. DO NOT
touch the bit and never allow it to come into contact with combustible materials when hot.
• Always use a suitable lubricant or cutting fluid and drill at appropriate speeds.
• Only apply moderate pressure to the drill bit, ensuring efficient cutting and prolonged drill
bit life
• Use a countersink bit to remove sharp burrs from the hole, preventing cuts and other kinds
of injury

Accessories

• A full range of accessories including drill bits, screwdriver bits and wire brushes, is available from
your Silverline stockist
• Spare parts can be obtained from toolsparesonline.com
Maintenance
WARNING: Always disconnect the tool from the power supply, before cleaning or carrying
out maintenance.
General inspection
• Regularly check that all the fixing screws are tight. They may vibrate loose over time
• Inspect the supply cord of the tool, prior to each use, for damage or wear. Repairs should be
carried out by an authorised Silverline service centre. This advice also applies to extension cords
used with this tool
Lubrication
• Lubricate all moving parts with a suitable lubricant spray, at regular intervals
Cleaning
WARNING: ALWAYS wear protective equipment including eye protection and gloves when cleaning
this tool.
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the device's service life
• Clean the body of your tool with a soft brush, or dry cloth
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent
on a damp cloth is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
• If available, use clean, dry, compressed air to blow through the ventilation holes (where
applicable)
Brushes
• Over time the carbon brushes inside the motor may become worn
• Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking
• If you suspect that the brushes may be worn, have them replaced at an authorised service centre
8
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: silverlinetools.com/en-GB/Support
UK Address:
Toolstream Ltd.
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
EU Address:
Toolstream B.V.
De Keten
00004
5651 GJ
Eindhoven, Netherlands
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
• For long-term storage, remove batteries and store separately
Disposal
Li-ion batteries should not be disposed of with household waste. If you do not know of a li-ion
battery recycling centre in your area, contact your local authority or original dealer for advice on
disposal of li-ion batteries.
Always adhere to national regulations when disposing of power tools that are no longer functional
and are not viable for repair.
• Do not dispose of power tools, batteries or other waste electrical and electronic equipment
(WEEE), with household waste
• Contact your local waste disposal authority for information on the correct way to dispose of power
tools and batteries

Publicité

Table des Matières
loading

Table des Matières