Télécharger Imprimer la page

Conrad 672329 Mode D'emploi page 2

Montre automatique dob

Publicité

Les langues disponibles

Les langues disponibles

O P E R A T I N G I N S T R U C T I O N S
Automatic Watch DOB
Item-No. 67 23 29
Intended Use
The product intended to be used as a wristwatch. It shows you the time in hours, minutes,
seconds, date, day, month and year.
Your watch is powered by winding the clockwork using the crown or by the rotor in the automatic
mechanism.
Any use other than described above is not permitted and can damage the product. There are
also risks involved.
Safety and Maintenance
Please read through the instructions completely, they contain important
information.
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequential
damage!
Nor do we assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions!
The warranty will be void in such cases!
• The unauthorized conversion and/or modification of the product is not permitted.
• The wristwatch must not be exposed to extremes of temperature, strong vibrations, intense
sunlight or heavy mechanical stress. This may damage the watch.
• This watch is not a toy and must be kept out of the reach of children, as they may swallow small
parts. Danger of suffocation!
• Do not leave packing materials unattended. It may become a dangerous plaything for children.
Danger of suffocation!
• If the strap becomes damp or wet, let it dry thoroughly. Wearing the watch for a long time with
a damp wrist, can lead to discoloration of the strap and possibly lead to irritation of the skin.
Furthermore, this might reduce the lifetime of the watchstrap.
• Only clean the exterior of the wristwatch with a soft, slightly damp cloth or a dry brush. Never
use aggressive cleansing agents or chemical solutions because these might damage the
surface of the case or impair the operation of the watch.
Operation
Setting the time
• Pull the crown (E) into position 2
• Turn the crown (E) and set the correct time.
• Push the crown (E) back into the normal
position 1.
Setting the Date, Weekday, Month and Year
• They are set using the buttons (A), (D), (F)
and (H):
(A) sets the year in the display (B).
(D) sets the month in the display (C).
(F) sets the date in the display (G).
(H) sets the weekday in the display (I).
• Press the corresponding button with a sharp object, until it reaches the correct setting.
Do not set the buttons between 22:00 and 2:00, because between these times, the
time is automatically set by the watch.
If the clock changes the date and weekday at 12 (noon), set the time 12 hours ahead.
Set the correct date again, if necessary.
Winding the Watch
• The watch's automatic mechanism runs automatically when the clock is worn on the wrist.
However, the watch will stop working when it is not worn for a long time.
• The clock can also be wound by hand, by turning the crown (E) (left in position 1). Do not wind
the watch too hard, as this can damage it.
• If the watch does not start again immediately, shake it briefly with a jerk to give it the appro-
priate start impulse.
Water and Shock Resistance
www.conrad.com
This watch is designed for normal use only. It must not be exposed to extreme shocks and
impacts. This might damage the clockwork.
Version 02/11
The watch's design is such that contact with water, as it arises in daily life (washing hands, water
spray, rain drops, etc.), has no adverse effect.
The watch is not suitable for swimming, showering or diving. Do not immerse the watch
in water. Leave the crown (E) in the normal position and do not turn it if the watch is wet;
otherwise water could leak in.
Accuracy
The accuracy of the watch should be checked after it has been use for about a month.
In case of major deviations, please contact a watchmaker and let him/her adjust the accuracy.
Technical Data
Running time:
Bearing jewels:
Water tightness:
© Copyright 2011 by Conrad Electronic SE.
38-40 hr
29
3 ATM
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.

Publicité

loading