Safety Instructions; Lithium Battery - Stanley BL50CK Instructions D'emploi

CORDLESS SCREWDRIVER WITH LITHIUM BATTERY
Technical data
Battery charger Voltage and
Frequency:
Voltage:
No load speed:
Bit size:
Battery type:
Charger current:
Charge time:
Read the following instructions and precautions before
using this product. Store this manual in a safe place.
User instructions
Range of use: Doing up an undoing screw. Use
machine, changing unit and accessories (follow maker's
specifications) only for the specified range of applications!
All other applications are expressly excluded.

Safety instructions

- Do not use machines, attachments and chargers for
works other than those for which they are designed for.
- Before drilling holes or screwing into a wall, in case of
doubt check with a metal-/voltage detector that you are
not breaking into an electricity, gas or water supply line.
- Before you lay down the drill/screwdriver, make sure
that all moving parts have come to a stop.
- Avoid frequent stalling when screwing or drilling, as it
could damage the batteries.
- Only connect the charging device to a 230 V AC supply.
- Charge the screwdriver battery only with the appropriate
charging device.
- The charging device and the screwdriver must be
protected from moisture.
- Do not use the charging device in the open.
- Never expose batteries to temperatures above 50 °C.
- Warning: Do not short out the contacts of battery or
charger.
- Respect the polarity "+/-" when charging.
- Do not throw batteries in fire.
Batteries use and care
Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against continuous
intense sunlight, fire, water, and moisture. Danger of
explosion.
In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air and seek
medical help in case of complaints. The vapours can
irritate the respiratory system.
Use the battery only in conjunction with your STAYER
power tool. This measure alone protects the battery
against dangerous overload.
ENGLISH
12
Use only original STAYER batteries with the voltage
listed on the nameplate of your power tool. When using
other batteries, e. g. imitations, reconditioned batteries or
other brands, there is danger of injury as well as property
damage through exploding batteries.
120-230V
Do not continue to press the On/Off switch after the
50 - 60 Hz
machine has been automatically switched off. The battery
3,6 V
can be damaged.
The battery is equipped with a temperature control
200 rpm
which allows charging only within a temperature range
1/4"
of between 0 °C and 45 °C. A long battery service life is
3,6 V Li-Ion
achieved in this manner.
300 mAh Observe the notes for disposal.
Use only the battery chargers listed on the accessories
3-5 horas
page. Only these battery chargers are matched to the
lithium ion battery of your power tool.
The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the
first time.
The lithium-ion battery can be charged at any time
without reducing its service life. Interrupting the charging
procedure does not damage the battery.
The lithium-ion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit: The inserted
tool no longer rotates.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot
be subject to overload. When the load is too high or
the allowable battery temperature range of 0–50 °C
is exceeded, the speed is reduced. The power tool will
not run at full speed until reaching the allowable battery
temperature. position. Unintentional actuation of the On/
Off switch can lead to injuries.
Open the keyless chuck 2 by turning in rotation direction ,
until the tool can be inserted. Insert the tool. Firmly tighten
the collar of the keyless chuck 2 by hand in rotation
direction . This automatically locks the drill chuck.
The locking is released again to remove the tool when the
collar is turned in the opposite direction.
Charging
The battery-operated screwdriver has not been fully
charged at works. Before using for the first time charge
the screwdriver unit for 3-5 hours. To do this insert the
charger plug (5) into the charging socket (4) and connect
the charging. unit (6) to a power supply. The battery (9) is
charged in the screwdriver.

Lithium battery

Always chargeable. No memory effect. No self discharge.
Care!
Do not exceed the maximum charging time of 8 hours, as
there is a risk of overheating!
Reccomendation
Connect the unit up to a time switch.
12