Dremel 100 Consignes De Fonctionnement/Sécurité page 14

DM 2610029870 12-12_DM 2610029870 12-12.qxp 12/12/12 2:33 PM Page 14
BEARINGS
Models 100, 200 & 3000 have double ball
bearing construction. Under normal use they
will not require lubrication.
Cleaning
To avoid accidents always
! WARNING
dis connect the tool from
the power supply before cleaning or
performing any main tenance. The tool may
be cleaned most effectively with compressed
dry air. Always wear safety gog gles when
cleaning tools with compressed air.
Extension Cords
If an extension cord is
! WARNING
necessary, a cord with
adequate size conductors that is capable
of carrying the current necessary for your
tool must be used. This will prevent
excessive voltage drop, loss of power or
overheating. Grounded tools must use 3-wire
extension cords that have 3-prong plugs and
receptacles.
NOTE: The smaller the gauge number, the
heav i er the cord.
Use only Dremel
! WARNING
designed for this tool and may lead to personal injury or property damage.
The number and variety of accessories for the
Rotary Tool are almost limitless. There is a
category suited to almost any job you might
have to do — and a variety of sizes and shapes
within each category which en ables you to get
the perfect accessory for every need.
Refer to the DREMEL AC CES SORY ORDER
FORM for illustrations of the ac ces sories
available. These accessories may be found
at your local hardware, hobby or home
center deal ers.
Collets
If you expect to use a variety of accessories,
we recommend that in the beginning you
purchase a complete set of four collets. Store
Ventilation openings and switch levers must be
kept clean and free of foreign matter. Do not
at tempt to clean by inserting pointed objects
through openings.
CAUTION
!
parts. Some of these are: gasoline, carbon
tetrachlo ride, chlo rinated cleaning solvents,
ammonia and house hold detergents that
contain ammonia.
RECOMMENDED SIZES OF EXTENSION CORDS
120 VOLT ALTERNATING CURRENT TOOLS
Cord Size in A.W.G.
Toolʼs
Ampere
Cord Length in Feet
Rating
25
3-6 18
6-8 18
8-10 18
10-12 16
12-16 14
Dremel Accessories
®
, high-performance accessories. Other accessories are not
these so that you will have the proper size of
collet for any accessory or drill bit you want to
use. Currently, the 1/8", 3/32",1/32" and
1/16" collets accommodate all of the avail -
able Dremel accessories. 1/8" collets are
included in most rotary tool kits.
A mandrel is a shank with a threaded or screw
head, which are required when you use
polishing accessories, cutting wheels, sanding
discs, and pol ish ing points. The reason
mandrels are used is that sanding discs,
cutting wheels and similar accesso ries must be
replaced frequently. The mandrel is a per -
manent shank, allowing you to replace only the
worn head when necessary, thus saving the
expense of replacing the shaft each time.
14
DV-2610029870, Page: MUL (VAA), downloaded at: 2016.04.12_17:39:53, by PT-RT/MKB2_Nicole.Hayden
Certain cleaning agents and
sol vents damage plastic
Wire Sizes in mm 2
Cord Length in Meters
50 100 150 15 30 60 120
16 16 14 0.75 0.75 1.5 2.5
16 14 12 0.75 1.0 2.5 4.0
16 14 12 0.75 1.0 2.5 4.0
16 14 12 1.0 2.5 4.0 —
12 — — — — — —
Mandrels