protech MEGA PEAK 4500 Instructions

MEGA PEAK 4500
INSTRUCTIONS
INSTRUCTIONS
Introduction:
The unit is a Battery charger for 4-8pcs battery packs with Delta Peak Control and discharge function. The unit can adjust
the charging current and the charging current also can be show on the LCD display. The charger has output short circuit,
battery reverse connection protection and automatically detect the battery cells. There are battery temperature sensors
for over-temperature protection.
Technical data
Input voltage:
Output:
Main charging terminal:
Main charging terminal:
TX:
RX:
Instruction:
1. Please study this instruction sheet before charging.
2. Attach the charger or the cigarette lighter plug with the AC or DC mains. The red and green LED flash once respectively
and LCD display starts to work.
3. Insert the 4-8 cells battery pack into the main charging terminals according to the correct polarity. The "FAST" lights in
red to indicate the charging is in fast charging progress after pre-charging for 1 minute.
4. Keep the temperature sensors to contact battery packs well.
5. Adjust the charging current within 1 minute of fast charging and then please do not adjust the charging current to avoid
of effecting battery detect.
6. For Discharge: Press the "DISCHARGE" button during charging, the charger will switch to the discharge mode. The
"FAST" and "TRICKLE" LED flashes in turn and discharging current is displayed on the LCD display. When the battery is
empty, the charger will resume to fast charge mode.
7. The charger will automatically switch to trickle charge mode when charging is completed. The "TRICKLE" LED lights.
8. When the predetermined charging time (6 hours, which is controlled by the safety timer) is reached, the charger will
switch to trickle charge mode and the "TRICKLE" LED indicator lights.
9. If the battery temperature is too high, the charger will also turn to trickle charge mode.
10. For RX terminal: Insert 4.8V to 6V battery pack to the charger. The corresponding LED lights to indicate the charging is in
progress.
11. For TX terminal: Insert 7.2V to 9.6V battery pack to the charger. The corresponding LED lights to indicate the charging is
in progress.
12. Note: "FAST" LED flashes to indicate battery pack is defective or the battery cells excess the detected scope.
13. When the battery is full, disconnect the charger from the AC outlet, and then remove the batteries from the charger.
Warning:
1. For indoor use only.
2. Do not charge non-rechargeable batteries.
Adjustable fast charge current:
230V AC input: 0.1 à 4.5A
12V DC input: 0.1 à 5.5A
Liability exclusion
As manufacturer, PROTECH is not in a position to ensure that you observe the correct methods of operation when installing, using
and maintaining this product. For this reason we are obliged to deny all liability for loss, damage or costs which are incurred due to
the incompetent or incorrect use and operation of our products, or which are connected with such operation in any way.
PROTECH®
AC 230V~50Hz, DC 12-13.8V
4.8 - 9.6V (4-8 cells)
4.8 - 7.2V (4-6 cells)
7.2 - 9.6V (6-8 cells)
4.8 - 6V (4-5 cells)
Large LCD display.
Display the charge current /
discharge current.
Geelseweg 80 • B-2250 OLEN • BELGIUM
PRO10-E • PRO25-E
100 - 4500mA For AC-230V input
100 - 5500mA For 12-13.8V input
150mA
150mA
RX output: 4.8 - 6V 150mA
TX output: 7.2 - 9.6V 150mA
info@protech.be
UK
T0258
Magnetic temperature sensor
prevents overcharging from
Ni-MH battery packs.
www.protech.be