Product Disposal; Use Of The Product - Novellini SOLE 400x1000 Instructions De Montage

ENGLISH
To select the TURBO Function, proceed as follows:
1) Switch off the radiator by means of the ON/OFF key ( double
fast flash on LED indicating 26rd ).
2) Press the remote control button showing the thermometer
three times (the 19th and 26st LEDs flash together ). This
indicates that TURBO mode has been selected.
3) Switch on the radiator using the ON/OFF button (the 19th
and 26st LEDs fast flash to confirm).
4) At this point, the radiator is operating in TURBO mode. To
check, press the thermometer key which will indicate the
TURBO function set by means of the flashing of the two 19th
and 26st LEDs.
5) After 4 hours, the radiator will automatically switch to
normal function with set temperature of 26°C.
To interrupt the TURBO function in advance (before the
4 hours from start have passed ) switch off the radiator
using the ON/OFF key.
When next switched on, the radiator will operate normally.
CONNECTION OF THE RADIATOR TO THE AMBIENT
THERMOSTAT
If the temperature of the room needs to be controlled, when
the radiator is being installed, it is necessary to:
1- Open the power box.
2- Connect a thin cable that goes to a potential free contact of
an ambient thermostat (not supplied), be it electromechanical
or electronic, programmable or other, provided that a
potential free contact is used to switch the radiator on and off
(see procedures on pages 65, 66).

USE OF THE PRODUCT

By means of key B (switch) the towel rail warmer, radiator can
be switched on and off.
Once on, the led on the power unit will be lit to confirm the
system is ON.
By pressing key A (thermometer) several times, the required
room temperature can be selected. Every time this key is
pressed, the selected temperature flashes briefly.
Once the room temperature corresponds to that set on the
remote control, the radiator supply is automatically interrupted
and started again when the temperature has dropped.
The room temperature reading device is in the remote control.
The remote control unit must therefore be put in a proper
place (e.g. do not place the remote control unit in a drawer
when the system is operating or near to the radiator itself ).
LED
A - Thermometer
B - Switch
CLEANING
Always use mild and non-acidic products. Do not use acid-
based descaling products containing sodium hypochlorite
which is not suitable for the cleaning of painted surfaces,
chlorine-based abrasive detergents, or those containing
bleach or solvents. Never use abrasive sponges or rags.
INCONVENIENCES
Before calling technical Assistance:
• Check that electricity is supplied to the radiator socket (it
would suffice to connect another instrument temporarily to
the electric socket).
• Check that the Remote Control gives some kind of luminous
signal when the buttons are pressed. If this does not occur, try
to replace the batteries.
+
Attention
To ensure impermeability to the Remote control, the sealing
gaskets need to be positioned correctly.

PRODUCT DISPOSAL

For the disposal of the product or its parts, follow the local
regulations on matters of waste disposal. For Italy, Legislative
Decree n. 152 of April 3, 2006 will hold, and for the other EU
countries, Directive 2008/98/EC.
RECYCLING AND SAFEGUARD OF THE ENVIRONMENT
Your device was packaged carefully to make sure it is not
damaged during transport. To contribute to the protection of
our environment, we request you to dispose of the packaging
material correctly.
Disposal of used equipment
The equipment bearing the mark seen on the side, must not
be gathered and disposed of separately. The disposal of used
equipment must be performed in conformity with the local
provisions and laws governing such matters.
WEEE DECLARATION
Novellini S.p.a.
Declares that the item: SOLE Radiator
conforms with the European directives on
Waste Electrical and Electronic Equipment Directive (WEEE)
2012/19/EU.
-18-
sealing
gaskets