Technical Data; Before Starting The Equipment - Hurricane HKSE 85/1 Kit Instructions D'origine

4. Technical data

Rated voltage: .................................230V ~ 50Hz
Power input: .......................... S2 20 min 85 watts
Idle speed: ..........................................5500 min
Adjustment angle: ............35° to the left and right
Grinding wheel Ø (inside): ......................... 23mm
Grinding wheel Ø (outside): ............ max. 108mm
Grinding wheel thickness: ....................... 3.2 mm
Protection class: ............................................ II/
Weight: .......................................................1.9 kg
A load factor of S2 200 min (intermittent periodic
duty) means that you may operate the motor
continuously at its nominal power level (85 W) for
no longer than the time stipulated on the speci-
fi cations label (20 minutes ON period). If you fail
to observe this time limit the motor will overheat.
During the OFF period the motor will cool again to
its starting temperature.
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
L sound pressure level ........................ 75 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 88 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 61029.
Grinding
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
Anl_HKSE_85_1_Kit_SPK7_BH.indb 18 Anl_HKSE_85_1_Kit_SPK7_BH.indb 18
-1
= 2.38 m/s
2
h
2
- 18 -
GB
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Assembly (Fig. 3-6)
•
Place the chain clamping mechanism in the
chuck (Fig. 3) and screw from underneath
using the star screw (Fig. 4)
•
Before starting the chain sharpener, fasten
it securely to a suitable surface (e.g. a work-
bench) at a suitable place (protected against
dust, dry, well-lit) using M8 fixing screws and
washers (Fig. 5)
•
Make sure when doing so that the mounting
plate of the chain sharpener is pushed 8 cm
onto the surface (Fig. 6)
04.08.2017 09:54:22 04.08.2017 09:54:22