Lock Function - Ndustrio T Serie Manuel D'instructions

15°. Reaching set temperature, and full device operation are no
more guaranteed beyond this range.
3.2.4 SETTING AND
PARAMETERS:
This function can only be accessed provided the Lock has not been
enabled!!
If you do not wish to start the oven, but want to change the settings
for one of the three parameters (ceiling temperature, floor
temperature, cooking time), use the arrow keys. Each time the right
arrow or left arrow key is pressed, one of the three values will be
selected (highlighted in bold).
On T64E, the corresponding display flashes; you can select four
parameters: ceiling temperature, floor temperature, baking time and
baking program. The selected parameter will start flashing. If you
select the ceiling and floor temperature, the display shows the set
point value. If you select the baking program parameter the
temperature display will show the set points for that program.
Once the value required has been selected, use the up and down
arrow keys to change the value.
NOTE: The above operation can also be carried out during
cooking, and in both cases if modifications are made to one of the
values from a generic program, the oven will automatically
"quit" that program and revert to "manual" mode.
TT98E only: It is possible to select the number of temperatures that
can be displayed and set:1, or 2, or 4.
To set the number of temperatures displayed, press and hold down
the OK and left arrow keys.
Then select one of the three options (1 temperature, 2 temperatures, 4
temperatures) using the up and down arrow keys.
Press OK to confirm. If the oven is set to 4 temperatures, the
maximum difference between floor and ceiling is 15°C and it is
30°C between the various temperatures (see example in fig.30
part. F) (in the 4 temperature mode the CEILING-FLOOR SET
POINT TEMPERATURE RESTRICTIONS function of point 3.2.18
is not enabled).
- Maximum set point temperature allowed 400°C (T75E-T97E) or
320°C (T64E-TT98E).
- Minimum Standard cooking time 2 minutes, 30 seconds on T64E
- Maximum Standard cooking time 20 minutes
The conveyor belt gear motor is fitted with a reverse rev control
(T75E-T97E-TT98E only) which, regardless of the weight on the
belt, guarantees an even transit time
To check the transit time on the T75E and T97E, it is necessary to
measure the time from the moment of entry at the outer side of the
baking chamber to the moment of exit at the outer side of the baking
chamber.
To check the transit time on the T64E - TT98, it is necessary to
measure the time from the moment of entry at the outer side of the
baking chamber to the moment of exit at the outer side of the baking
chamber. On the T64E - TT98E it is also possible to set cooking time
to zero and therefore, the belt will remain idle
3.2.5 RUNNING ONE OF THE 20 PROGRAMS
T75E-T97E-TT98E:
If, when the oven is turned on, it is set to "manual" or to a different
program from the one required, simply use the buttons provided ( P1,
P2, P3 or P4) as described below to select another program:
press briefly to set the relevant program (1,2,3 or 4); press for
longer and a window will be displayed requesting that another
button be pressed for the second figure (it must be pressed within 5
seconds, otherwise only the first figure will be considered); in this
way it is possible
programs(1,2,3,4,11,1213,...,44);
at this point the data for the chosen program will be displayed on
the monitor, after which you can start cooking by pressing the Start
button (see point 3.2.3)
T64E (reference Fig. 29b
If, when the oven is turned on, it is set to "manual" or to a different
program from the one required, simply use the display (item D will
flash) with the "Left Arrow" (or "Right Arrow"), then select the
MODIFYING COOKING
to select 20 different
desired program indicated by "Pr □ □" with the "Arrow up" or
"Arrow down". If you browse through the programs display, ceiling
temperature, floor temperature and baking time show the set values
of the selected program.
If the program required is reached, press OK to confirm. If ok is not
selected after a few seconds the display will show the previously set
program.
The T64E provides 20 programs and two special programs: STEP
and RETURN.
The STEP program (indicated in the D display by "StEP") can be
used when there is a work pause. The conveyor belt can then be
enabled for a single baking module. To use this program, select the
STEP item from the program list. The conveyor belt then stops. Place
the product at the edge of the belt, then press the "P / Hotkey" to start
baking: the belt will start moving to allow the transit of the product
in the set time. After this the belt will stop until you press "P /
Hotkey".
The RETURN program (shown in the D display by "retu") can be
used for baking times higher than the maximum allowed (or taken
out of the oven on the same side in which it is placed in the oven).
The conveyor belt can then be enabled for a double baking module.
To use this program, select the RETU item from the program list.
The conveyor belt then stops. Place the product at the edge of the
belt, then press the P / hotkey to start baking. The belt will start
moving, then the first products will be received within the time set
then the second ones in the opposite direction also within the baking
set time. Example:12 minute- set cooking time, for a total cooking
time of 24 minutes. This setting is not provided for standard
operations.
NOTE: When using the special STEP and RETURN programs,
after 2 minutes from the last bake, if no key is selected, the oven
automatically enters the ECONOMY mode shown in the
"ECO2" display. Once a new bake or a different cooking
program is selected, the oven returns to the standard setting
mode.
3.2.6 SETTING A PROGRAM
This function can only be accessed provided the Lock has not been
enabled!!
If you wish to store the 3 characteristic values for a cooking
operation (ceiling
temperature), after setting them as required using the arrow keys (see
point 3.2.4), press the "Program" button.
T75E-T97E-TT98E:
The monitor will display the question: what program do you want to
store? Select the program using keys P1 P2 P3 or P4 using the
method described in point 3.2.5.
T64E
The message "Pr01" is flashed on the display (figure 29b item D).
Select the program to be stored with the "Up Arrow" and "Down
Arrow". Press OK to confirm.
3.2.7 MODIFYING A PROGRAM
This function can only be accessed provided the Lock has not been
enabled!!
If you wish to modify a program that has already been stored, you
must first call it up by pressing the relative key as of section 3.2.5.,
then modify the values using the arrow keys. As soon as one of the
three parameters is modified, the control unit switches to manual
mode. To store the new values, proceed as already described in
section 3.2.6.
NOTE: On T64E when using the special STEP and RETURN
programs, parameters are modified automatically every time a
baking parameter is changed!
3.2.8

LOCK FUNCTION:

This function can be used to block certain operations, for safety
purposes:
The following functions are disabled:
- Storing programs (if the "Program" key is pressed nothing will
happen)
- Variation of cooking parameters during or before cooking (it is only
possible to use one of the stored programs)
- Setting the Timer (where present)
The following functions are still enabled:
UK/5
temperature, floor temperature, cooking