turck TX707HB-P3CV01 Mode D'emploi page 5

TX707HB-P3CV01
EN
Quick Start Guide
HMI – TX707HB-P3CV01
Other documents
The following additional documents are available online at
■
Data sheet
■
Instructions for use for TX series
■
EU declaration of conformity (current version)
For your safety
Intended use
The HMIs (Human Machine Interfaces) of the TX700 family are used to control,
operate and monitor machine processes. The high brightness versions of the
TX700 series are designed for use in very bright environments due to their high
sunlight readability.
Any other usage shall be considered improper and Turck shall not be held liable
for any resulting damage.
General safety instructions
■
The devices may only be assembled, installed, operated, parameterized and
maintained by professionally-trained personnel.
■
The devices only meet the EMC requirements for industrial areas and is not
suitable for use in residential areas.
■
The devices may only be used in accordance with applicable national and
international regulations, standards and laws.
■
Do not open the devices under voltage.
Note on explosion protection (USA and Canada only)
■
The devices are approved for operation in hazardous areas only in the USA
and Canada and do not have ATEX approval.
■
The devices are suitable for the use in Class 1, Division 2, groups A, B, C and D
hazardous locations or for the use in non-hazardous locations.
Product description
Device overview
See fig. 1
Functions and operating modes
The devices of the TX700 series combine control, operation and monitoring by a
CODESYS V3 PLC with web visualization to a complete control unit. The
CODESYS V3 control of the TX700 has the functions PROFINET controller,
EtherNet/IP scanner and Modbus TCP as well as Modbus RTU master. Additionally
the devices of the TX700 family can be used as Modbus TCP as well as Modbus
RTU slave.
Additional functions
■
Ethernet TCP/IP or UDP/IP communication
■
OPC-UA server and client, MQTT
■
Serial communication via RS232, RS485 and RS422
Installing
See fig. 2 and 3
A = TX7...
B = installation cut-out
Tighten the fastening screws until the brackets are firmly in contact with the
➤
device. The minimum tightening torque to guarantee protection class IP66 is
130 Ncm.
Do not cover the ventilation slits in the device.
➤
TX... Brackets included in delivery
TX707HB 4
Connecting
DANGER
Ignitable atmosphere
Explosion by ignitable sparks
Do not disconnect the device in an ignitable atmosphere when energized.
➤
Disconnect the device from the power supply before replacing or connect-
➤
ing modules.
Connectors and slots
See fig. 4
Connector/slot
www.turck.com
1
2
3
4
5
6
7
8
WARNING
Unsuitable wiring
Loss of suitability for Class 1, Division 2
The power, input and output (I/O) wiring has to be done in accordance with
➤
Class I, Division 2 and in accordance with the authority having jurisdictions.
For U.S. in accordance with Article 501.10 (B) of the National Electrical Code,
NFPA 70 and for Canada in accordance with Section 18-1J2 of Canadian
Electrical Code.
NOTE
Devices of protection class III according to EN 61140 or Class 2 according to UL
standards: All connections are SELV connections.
Power supply
Connect the device to the voltage supply according to fig. 5 and 6.
➤
DANGER
Wrong selection of power supply
Danger to life due to overvoltage and electric shock!
Operate the device only on SELV voltage sources according to European
➤
standard or on Class 2 voltage sources according to UL standard
Grounding the device
The minimum conductor cross-section for the ground connection is 1.5 mm².
Ground the housing via the grounding screw on the back of the housing.
➤
Connect terminal 3 on the power supply terminal block to ground.
➤
Serial interface
See fig. 7
Pin
1
2
3
4
5
6
7
8
NOTE
When used as RS485 interface, pins 1 and 2 as well as pins 3 and 4 must be
connected externally.
Function
USB port , V2.0, max. 500 mA (for maintenance only)
Ethernet port 2 (10/100 Mbit)
Ethernet port 1 (10/100 Mbit)
Serial interface
Ethernet port 0 (10/100/1000 Mbit)
Power supply
SD card slot
2 extension slots for plug-in modules
RS232
RxD
TxD
CTS
RTS
+5 VDC output
GND
n. c.
Shield
© Hans Turck GmbH & Co. KG | 1000015595 2020-11 DE EN FR
RS422/RS485
CHB-
CHA-
CHB+
CHA+
+5 VDC output
GND
n. c.
Shield