General Instructions - Tecnoinox 716033 Mode D'emploi

ELECTRIC FRY-TOPS

General Instructions

The appliance referred to in this manual has been manufactured in
conformity to the following Directives: "Low Voltage" 2006/95/CEE and
2004/108/CEE and 2006/42/CEE "Electromagnetic Compatibility.
The technical specifications of the appliance can be found on the
data plate located inside the control panel |T| fig.1, which can be
removed by loosening the two screws under the panel.
The appliance must be installed by a qualified technician according to
the regulations and directives in force in the country where it is
installed, as well as the instructions in this manual. The appliance must
only be used by trained personnel and only for the purpose for which it
has been designed. The appliance should be checked once a year by a
qualified technician.
Remove the packaging from the appliance as well as the protective
plastic sheet, and, if necessary, remove traces of glue with a suitable
solvent. To dispose of the packaging, follow local directives.
Connection to the distribution network
Before connecting the appliance note the specifications: voltage,
frequency, number of phases and power on the data plate, relevant to
the power input of the same. The installer must make the connection
after having installed a main switch, which should disconnect every pole
supplying electrical power to the appliance. The switch supplying
electrical energy to the appliance must have a minimum distance of at
least 3 mm between the poles when the contacts are open. The switch
must be easy to reach. The power lead must not be installed anywhere
near heat sources and the temperature of the place in which the cable is
installed must not rise above 50°C. The cable must be protected by a
rigid metal or plastic tube. The appliance is supplied without a power
cable. The electric cable used to supply power to the appliance must at
least meet H07 RN-F standards. It must have the minimum section
indicated in the table (fig.1). To reach terminal board |M| fig.2, remove
the control panel by loosening the screws on the lower part of the
General Instructions
Connection to the distribution network, installation, and
maintenance of the appliance must only be carried out by qualified
technicians only, in observance of all applicable regulations!
Special instructions for using chrome-plated hot plates
The first time the hot plates are used we recommend cleaning them
with water and a neutral detergent then rinse and dry the hot plates
and heat to a temperature of 200° C for one hour. Stainless steel
spatulas with rounded corners should be used for cooking the food. Use
a sharp scraper with rounded sharp edges for cleaning. To avoid
Turning the appliance on
 Switch the power on using the switch upstream of the appliance.
 Turn knob |A| fig.2 so that the indicator mark on the control panel
corresponds to the desired cooking temperature.
Turning the appliance off
 Turn the knob to |0|.
PART 1 - INSTALLATION
When installing the appliance, the following regulations must be
observed:
 Applicable national laws in force;
 Regional and/or local regulations, such as building codes;
 Directives and regulations of the local electricity board;
 Accident prevention regulations in force;
 Fire prevention regulations;
The appliance should be installed under an extractor fan for removing
cooking fumes. The appliance can be installed alone or in line. Respect a
minimum distance of 80mm between the appliance and any walls
made of flammable material, partitions, kitchen furniture or nearby
equipment. The surfaces in contact with the appliance must be covered
with non-combustible heat insulating material. The appliance, and
especially the power lead, must not be installed anywhere near heat
sources and the temperature of the place in which the appliance is
installed must not rise above 50°C.
panel. Following the indications in the wiring diagram, connect the
wires of the power cable to the terminal board. The appliance must be
connected to a good earth. There is a screw marked with the symbol
near the terminal board where the earth conductor should be
connected. Make sure you slide the cable through the relevant hole |P|
fig.2 near the terminal board, hold the cable in place until you can block
it with cable clamp |AL| fig.1. The appliance must be connected to a
good earth. The appliance must also be connected to an equipotential
earth. Connect the earth with the screw marked
the appliance. The equipotential wire must have a section of 10 mm
The Manufacturer declines any responsibility for damage caused
by improper or incorrect installation or maintenance of the appliance, or
failure to observe safety regulations!
PART 2 - USE
This appliance has been designed exclusively for cooking food. It has
been designed for use in community kitchens and must only be used by
qualified personnel.
The unit must never be left unattended when it is being used!
Care must be taken when using the appliance because the cooking
surfaces are very hot.
scratching the grill-top, the entire length of the scraper edge must
come into contact with the surface; don't use the corner of the scraper.
Don't use vinegar or lemon juice when cooking to preserve the shiny
surface of the heating unit. When the fry-top with the chromed plate is
on, the plate doesn't appear to be hot: therefore take the greatest care.
 When the green indicator light is on, the appliance is supplied with
electric power.
 Switch the power off using the switch upstream of the appliance.
GB/IE - 1 -
on the rear panel of
2 .