Profile 100000155 Terral Mode D'emploi page 13

ELECTRIC CONVECTOR HEATER
100000155 Terral
Thank you for purchasing this Profile product. Caution: It
is important that you read this manual before using the
product Then keep this manual in a safe place.
Technical information
 Mains voltage: 220V
 Guarantees fast warming up
 3 positions: 1200W
 For space of max. 20m²
 With protection against overheating
 With adjustable, built-in thermostat
Connection
The heater is supplied with a plug. Never use the
appliance with a
damaged cable and/or plug, after the heater has not
been working properly, or if it has been damaged in
whatever way.
The replacement of a cable and/or socket plug may only
be done by a qualified professional who is familiar with
the applicable requirements.
Installation
Vertical position:
 Carefully turn the radiator on its side to assemble the
feet.
 Fit each foot (fig. 1) and tighten them with the screws
supplied.
 Two screws are needed for each foot. Do not use the
radiator if the feet are not properly assembled!
Fig. 1
Operation and functions
Operation:
 Switch the power switches to position 0.
 Insert the plug in the socket.
 Press the switch(es) with the required wattage
to switch the radiator on.
Use:
 The thermostat will automatically maintain your desired
room temperature.
 Switch on one or a number of switches depending on
the speed at which you want to obtain the desired
temperature.
Switch 1: 1200W
o
Switch 2: 1800W
o
Switches 1 and 2: 3000W
o
–
240V AC (50/60Hz)
– –
1800W 3000W
 Turn the thermostat clockwise until you hear a click.
This sound means that the heater is now switched
on.
 The anti-frost protection is switched on in the
minimum position.
 Turning the thermostat clockwise increases the
temperature set. Conversely, turning it anticlockwise
lowers the temperature set.
 The thermostat automatically switches the heating
on and off when the set temperature has been
reached.
Note
 Allow the radiator to fully cool down before moving it
and always use the handle for this purpose.
 Protection against overheating: if this is activated the
radiator switches itself off. Then switch the radiator
off and pull the plug from the wall socket. Allow it to
cool down and remove any hindrances before using
the radiator again.
Cleaning
 We advise you to carefully clean the heater once a
month to remove dirt and dust. This ensures the
heater will continue working efficiently and safely.
 Always switch the thermostat off and remove the
plug from the socket. Make sure the appliance has
fully cooled before cleaning.
 Clean the housing with a clean, soft and lightly
moistened cloth. Never clean the heating elements
or thermostat in water. Blow as much dust as
possible off the heating elements. This extends the
life of the appliance and eliminates fire risks.
 Let everything dry thoroughly before switching the
heater on again. Do not use any detergent, wax or
cleaning agents; these can react under the influence
of heat and cause the colour to deteriorate.
 Save the box for storage during periods you are not
using the appliance. When being stored the heater
must also be protected against dirt and dust.
Guarantee
The guarantee period is 2 years and commences on
the date of purchase. During the guarantee period
Eltra NV resolves any defects caused by material or
manufacturing faults. Eltra NV may optionally either
repair or replace the defective appliance.
Eltra NV is not obligated to repair or replace units if the
defect is a result of damage, misuse, modification or
changes made after the date of purchase.
Bring the defective device, along with the original sales
receipt, back to the shop where the unit was
purchased. Always include a note describing the
problem.
Damage
Eltra NV can under no circumstances whatsoever be
held responsible for damage of whatever nature if the
appliance was not correctly installed according to the
EN -
1