Charging Battery; How To Use - IRIS IC-FDC1U Serie Guide D'utilisation

CHARGING BATTERY

Do not charge battery with other charger except the original brand .
Battery does not come fully charged . Please charge to full power before first use . Full charge
WARNING
will take approximately 3 .5 hours .
Please do not use the device while charging .
1. Please put the battery into the vacuum cleaner.
Place the battery into the vacuum . Press battery into the socket until you
hear a clicking sound .
*Failure to fully insert the battery into the socket will affect operation and
can result in injury or damage .
Please insert the battery tightly and
firmly into the socket until there is a
clicking sound .
2. Plug the charger plug into the power outlet.
3. Insert the charger into power socket.
Please insert the charger into the power socket tightly and firmly .
* The Battery Level red indicator light means the product has started
charging .
4. Battery is fully charged .
The indicator light will shut off when done charging .
• For first time use or non-use for more than 6 months, please
charge 2 or 3 times before use to achieve full charge .
• If more than 10 days since last use, charge before next use .
• Continual charging will decrease charge hold time .
• Charging and running time will vary due to temperature and
operating conditions .
• Charge between temperatures of 41°F/5°C and 95°F/35°C .
Charging in too low or too high temperatures can cause decreases
in working time or lengthening in charging time .
• Charger will be warm . This is normal .
5. Removing the battery.
Press the battery release button and take out the battery .
Battery
Insert until clicking
sound is heard
Battery release
button
Clicking
Sound
Power outlet
Battery Charger plug
Battery Level indicator light
High
Low
Battery Level
Safety Lock
(hold for 3 sec)
Standard charging time about 3 .5 hours
5

HOW TO USE

Do not use this vacuum cleaner to clean the following objects:
Liquid, wet litter/debris, powder, broken glass, sharp or pin type objects, sand or gravel, plastic
bags .
Please do not clean large amounts of litter/debris in one pass to avoid blocking the intake port and
CAUTION
decreasing suction .
Do not use on floors, walls or furniture . Do not pull on the main body and avoid hitting walls or
furniture .
Empty the dust cup after use to avoid decreased suction or issues with the sensor .
1. Adjust the collection head angle.
Please place the vacuum on the floor, then adjust the angle up
and down by hand .
• Please adjust the vacuum body to the horizontal position,
which should be used for soft surfaces such as bedding .
• The collection head is fastened in horizontal position by a
magnet to keep it in place during use .
2. Unlock.
Hold the Menu ON/OFF button for 3 seconds, wait for the Safety
Lock indicator to light up, then start cleaning as directed below .
• Safety Lock will automatically lock again after one minute
of non-use .
• Device will not work when locked . Pressing the Menu ON/
OFF button to start when it is locked will cause the Safety
Lock light to blink .
3. Start the product.
Pressing the Menu ON/OFF button changes the mode .
• Press the Menu ON/OFF button to change to High mode .
• Press the Menu ON/OFF button again to change to Low
ON
mode .
Charging
4. When finished cleaning.
OFF
Press the Menu ON/OFF button to change the mode until the
Finished
vacuum stops and the indicator light shuts off .
• Device will automatically lock after one minute of
non-use .
• Please follow step 2 to restart .
• Battery Level indicator light will blink when battery
power is low .
• When battery runs out of power, Battery Level
indicator light will blink rapidly before shutting off,
and motor will stop . Please recharge .
Storage position
Carpet or car cushion
material angle .
Bedding/soft
materials
angle
Safety Lock
High
indicator light
Low
Battery Level
Safety Lock
(hold for 3 sec)
Menu
ON/OFF
Indicator light
High
Low
Battery Level
Safety Lock
(hold for 3 sec)
Menu
ON/OFF
Indicator light
High
Low
Battery Level
Safety Lock
(hold for 3 sec)
Blinking: Low power
Blinking rapidly (then off): No power
Menu
ON/OFF
6
High
Low
Stop