Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

V8043C,D,F & G
Motorized Zone Valves
APPLICATION
The V8043 Motorized Zone Valve provides two-position
(open-close) control of supply water for baseboard
radiation, convectors, fan-coil units, etc. It uses a two-wire,
24-volt control circuit and requires a SPST thermostat.
Integral end-switch models permit the sequencing of
auxiliary equipment.
FEATURES
• Quiet, dependable operation is provided by motor-
operated powerhead and swing-type ball valve.
• Unique rotating ball plug that seats on a different part
of its surface on each closing.
• Closes against the flow of water to assure quiet
operation.
• Manual opener moves ball away from seat allowing
valve to be installed without disassembly.
• Manual operation on power failure.
• Easy servicing because the entire powerhead assembly
can be replaced without removing valve body from line.
Optional accessory fittings can be provided to facilitate
convenient removal of the entire zone valve unit.
• Low power requirements allow four valves to be
operated from a single 40 VA transformer.
• Integral end-switch on F & G models to permit
sequencing of auxiliary equipment.
• Choice of sweat, female NPT and flare (with union-flare
adapters) body styles.
• Compact construction permits fitting under cover of
most baseboards.
SPECIFICATIONS
Models:
V8043C - Normally closed.
V8043D - Normally open.
V8043F - Normally closed with integral line voltage end
switch.
V8043G - Normally closed with integral low voltage end
switch.
Body Styles: All models have straight through pattern
only. 1/2", 3/4", or 1" sweat or female NPT, or 3/8" flare.
Inlet fittings can be provided with or without 1/16"
diameter bypass or bleed.
INSTALLATION INSTRUCTIONS
V8043C,D
V8043G
Close-off Water Pressures and Capacity (Cv) Ratings:
All models -
50 psi for 1.0 Cv
20 psi for 3.5 Cv (Standard Rating)
8 psi for 8.0 Cv
Static Pressure Rating: Both 125 psi (VC8043C/D/F/G
1000 series) and 300 psi (V8043C/D/G 3300 series)
models available.
Temperature Rating:
Liquid - 4° C to 93° C (40° F to 200° F).
Ambient - 4° C to 52° C (40° F to 125° F).
Steam - Consult your local Resideo representative.
Humidity Rating: 5-95% RH (non-condensing)
Atmosphere: non-corrosive, non-explosive
V8043F
272704A
95C-10926EF-04

Publicité

Table des Matières
loading

Sommaire des Matières pour Honeywell Home V8043C

  • Page 1 • Choice of sweat, female NPT and flare (with union-flare Static Pressure Rating: Both 125 psi (VC8043C/D/F/G adapters) body styles. 1000 series) and 300 psi (V8043C/D/G 3300 series) • Compact construction permits fitting under cover of models available. most baseboards.
  • Page 2 V8043C,D,F & G MOTORIZED ZONE VALVES Wiring Connections: Thermostat Heater Setting: For heat anticipation: ‘C’ and ‘D’ Models - 2 low voltage 0.5 m (18 in.) leadwires 0.32 Amps. with strain relief. Replacement Powerheads: ‘F’ Model - 5 screw terminal board. Includes “blind” termi- 125 psi Models: nal for transformer and thermostat wiring convenience.
  • Page 3 V8043C,D,F & G MOTORIZED ZONE VALVES CONDUIT COVER SWEAT LEADWIRES TERMINAL BOARD FOR V8043F CLEARANCE FOR COVER 4-7/8 (124) REMOVAL END SWITCH AUTO OPEN AUTO OPEN FNPT 3/8 FLARE CLEARANCE NECESSARY FOR COVER REMOVAL FLAIR-TO-SWEAT UNION ADAPTER DIMENSION IN INCHES (MM)
  • Page 4 V8043C,D,F & G MOTORIZED ZONE VALVES INSTALLATION REMOVING AND MOUNTING OF ACTUATOR FOR 300 PSI CAUTION MODELS Normally it is not necessary to remove the powerhead from the valve body during REMOVING THE ACTUATOR FROM THE VALVE BODY installation. The valve must be disassembled...
  • Page 5 V8043C,D,F & G MOTORIZED ZONE VALVES WIRING All wiring must conform to local electrical codes and ordinances. Refer to Fig. 4 to 7 for wiring connections. THERMOSTAT THERMOSTAT ENCLOSURE FOR (TYPICALLY T86) (TYPICALLY T87) TRANSFORMER END SWITCH TERMINALS TO CIRCULATOR...
  • Page 6 The Honeywell Home trademark is used under license from Honeywell International, Inc. This product is manufactured by Resideo Technologies, Inc. and its affiliates. Tous droits réservés. La marque de commerce Honeywell Home est utilisée avec l’autorisation d’Honeywell International, Inc. Ce produit est fabriqué par Resideo Technologies, Inc. et ses sociétés affiliées.
  • Page 7: Vannes De Zones Motorisées

    Vannes de Zones Motorisées V8043C, D, F, et G NOTICE D'INSTALLATION APPLICATION La vanne de zone motorisée V8043 assure la régulation tout ou rien (ouverte-fermée) du débit d'eau d'alimentation dans les plinthes chauffantes, les convecteurs, les ventiloconvecteurs, etc. Elle est asservie à...
  • Page 8: Accessoires

    VANNES DE ZONES MOTORISÉES V8043C, D, F, ET G Connexions de câblage: Réglage de la résistance anticipatrice de chaleur du thermostat: 0,32 A Modèles 'C' et 'D' - deux fils conducteurs basse tension de 0,5 m (18 po) avec serre-câble.
  • Page 9 VANNES DE ZONES MOTORISÉES V8043C, D, F, ET G COUVERCLE DE CONDUIT À SOUDER FILS CONDUCTEURS BORNIER POUR V8043F ESPACE POUR ENLEVER LE 4-7/8 (124) COUVERCLE END SWITCH AUTO OPEN AUTO OPEN NFPT 3/8 ÉVASÉ ENTRÉE SORTIE SORTIE ENTRÉE ESPACE NÉCESSAIRE POUR ENLEVER LE COUVERCLE ADAPTATEUR UNION ÉVASÉ-À...
  • Page 10: Montage

    VANNES DE ZONES MOTORISÉES V8043C, D, F, ET G POSE DÉPOSE ET MONTAGE DE L'ACTIONNEUR POUR DES MISE EN GARDE MODÈLES DE 300 PSI Normalement, il n'est pas nécessaire de retirer DÉPOSE DE L'ACTIONNEUR DU CORPS DE LA VANNE l'actionneur du corps de la vanne pour l'installation.
  • Page 11 VANNES DE ZONES MOTORISÉES V8043C, D, F, ET G CÂBLAGE THERMOSTAT (T87) Tout le câblage doit être conforme au code de l'électricité TRANSFORMATEUR et aux règlements locaux. Consultez les Fig. 4 à 7 pour les VERS connexions de câblage. 120 V...
  • Page 12: Fonctionnement

    The Honeywell Home trademark is used under license from Honeywell International, Inc. This product is manufactured by Resideo Technologies, Inc. and its affiliates. Tous droits réservés. La marque de commerce Honeywell Home est utilisée avec l’autorisation d’Honeywell International, Inc. Ce produit est fabriqué par Resideo Technologies, Inc. et ses sociétés affiliées.

Ce manuel est également adapté pour:

V8043dV8043fV8043g

Table des Matières