Publicité
Les langues disponibles
Les langues disponibles
Rotatable LED automobile lamp
Item no. 855238
Intended use
The LED automobile lamp serves as light source inside vehicles. This product may only be operated if it is
connected to a 12 V DC car power supply with the negative terminal of the car battery connected to the body.
It may only be installed and operated in vehicles supplied with this kind of voltage. Never connect the lamp
to any other voltage supply.
Use is only permitted in the car or closed rooms, i.e. not outdoors. Contact with moisture or dampness must
be avoided at all times. Through proper installation the user has to ensure that the lamp is protected against
moisture and dampness.
Any other use than the one prescribed above involves damaging the product and moreover involves the
danger of short circuits, fires etc. Please read all safety instructions contained in these operating instructions
and keep these for further reference.
This product fulfils the Economic Commission for Europe regulations related to
automotive electromagnetic compatibility.
The product is licensed for operation on public roads in vehicles, with the exception
of vehicles which run on rails and of agricultural and forestry tractors and all mobile
machinery.
Scope of delivery
• LED indoor lamp
• Mounting material
• Operating instructions
Safety instructions
Damages caused resulting from improper use and disregard of this operating instruction
are not covered by the warranty! We do not assume liability for damages to property, or
personal injury if the product is misused in any way, damaged by improper use, or any
failure to observe these safety instructions!
An exclamation mark in a triangle indicates important information in the operating
instructions.
• Unauthorised conversion and/or modification of the product are inadmissible due to safety and
approval reasons.
• Prior to commissioning, check the device for damage. If the device is damaged, it may not be
put into operation.
• The device may only be used with the 12 V DC vehicle power supply (with the negative terminal
of the battery connected to the body of the vehicle). Never connect the lamp to any other
voltage supply.
• Make sure the device is put into operation correctly. Please follow the operating instructions
carefully when doing so.
• Consult qualified staff, if you have doubts about how the equipment operates or about how to
connect it safely.
• Always check the lamp and the connection cables from time to time for damage.
• An expert must repair the product in case the lamp or the connection cables are damaged.
• Avoid heavy mechanical stress on the lamp and do not expose it to high temperatures, strong
vibration or dripping or spray water.
• Never pour out any liquids over the lamp. You run the risk of causing a fire or a fatal electric
shock. If any liquid should nevertheless penetrate the device, immediately disconnect it from
the power supply network and contact a specialist.
• The device does not belong in the hands of children. Keep it out of the reach of children.
• Observe the additional safety instructions in each individual section of these instructions, too.
• Packaging material could become dangerous toy for children. Never leave it lying around
carelessly.
• If any questions arise that are not answered in this operating instruction, contact our Technical
Advisory Service or other experts.
Mounting
Modifications to the vehicle which are made necessary through the installation of the
lamp must always be carried out in such a manner that neither the traffic safety nor the
designed stability of the car is impaired. If you are in doubt when selecting a place for
installation, consult your car dealer.
Before drilling the attachment holes make sure that the electric cables, brake lines, the fuel
tank or similar systems will not be damaged.
When using tools for mounting your device, observe the safety instructions of the
manufacturer.
1. Look for a suitable installation location.
2. Mark the holes for the screws at the place of installation. Use the device itself as a model for this.
3. Drill the holes for the fastening screws.
4. Fasten the lamp with the two enclosed screws.
When installing the lamp, take into consideration the risk of accident which can arise from devices
being torn away in case of an accident. Therefore, fasten each part securely and in a location
where it will not pose a risk to the passengers.
Connecting the power supply
The electric connection should always be carried out by a specialist. To avoid short cuts
and any resulting damage to the device, the negative terminal (earth) of the car battery has
to be disconnected first.
Version 01/14
Before reconnecting the negative terminal to the battery, ensure that the lamp has been
completely connected. Only use a volt meter or a diode test lamp for checking the voltage
on the vehicle system leads, as normal test lamps consume excessive voltage and
may thus damage the vehicle's electronics. When installing cables make sure that the
connection cables are not squeezed or damaged by sharp edges. Use rubber bushings
for passing points.
1. Connect the red connection lead with the positive voltage supply.
2. Connect the black connection lead with the negative voltage supply (earth).
Supply lines to the lamp must be protected with fuses. The fuse must be designed proportionately
to the cross section (mm²) of the supply line used, since it serves to protect the supply line laid
through the car body. Look for a suitable installation location.
Operation
The lamp is turned on and off with the switch next to the light output.
Care and maintenance
Always separate the lamp from the power supply before cleaning it.
The outside of the lamp should only be cleaned with a soft, dry cloth. Never use caustic cleaning agents or
chemical solutions as the surface of the housing could be damaged.
Bulb replacement
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical data
Operating voltage ........................................ 12 V/DC
Output .......................................................... 0.5 W
Current consumption ................................... 0.03 mA
Lamp ............................................................ 6 white LEDs (MR11)
Dimension (Ø x H) ....................................... 80 x 45 mm
1. Press the protruded sides and remove the cap.
2. Pull out the damaged bulb.
3. Insert the new bulb into the lamp holder and click the cap with the
housing.
4. Turn on the switch to make sure of illumination function.
These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2014 by Conrad Electronic SE.
V1_0114_02-KV
Publicité
