Nico 352-02701 Manuel page 4

352-02701 / 352-02702 / 352-02703
Read the complete user manual before carrying out the installation and activating the system. Keep
the manual for future reference.
1. DESCRIPTION
This is an adaptable and energy-efficient luminaire with a clean design. With its homogeneous lighting effect,
the lamp ensures superior lighting in all conditions. As the lamp is equipped with a built-in HF sensor, it only
switches on when necessary.
As soon as someone is detected, the light is switched on daylight-dependent. The lamp only switches on once
the set daylight condition (twilight level) is no longer reached and remains active as long as human movement
is detected (see Fig. 1a and Fig. 1b.).
This manual applies to the following lamp types:
352-02701
Colour white
These lamp types are also available without the built-in HF sensor (see reference numbers 352-08964,
352-08965 and 352-08966).
2. USE
Suitable for landings, corridors, hallways and sanitary areas.
Please note that the HF sensor covers a different detection area with ceiling (see Fig. 1a) or wall mounting
(see Fig. 1b).
In case of outdoor use, take into account that the HF sensor registers all movements. Movements of hedges,
leaves, raindrops and snowflakes may cause the sensor to switch on incorrectly. It is not recommended to set
up the sensor close to a street. Passing vehicles up to 20 m away may activate the sensor.
The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole
luminaire shall be replaced.
3. OPERATION
The HF movement sensor actively emits high-frequency electro-magnetic waves (5.8 GHz) and responds to
changes in the waves reflected by objects. If the sensor detects something, it switches on the light. After the
final detection, the sensor switches off the light after the switch-off delay (approx. 10 s to 5 min.) has lapsed.
The sensor can also detect movements through walls, doors and glass.
As the detection is the result of reflected waves (see Fig. 1c), the detection range changes according to the
mounting position. The speed and the type of object (a person, vehicle ...) strongly influence the detection range.
Before putting the lampshade back, check that the METER potentiometer (which determines the detection
range per metre) is set optimally.
By using the included protective metal brackets 351-27361 on either side, the sensor can be protected from
interference waves (see Fig. 8). Take this into account while mounting.
4. MOUNTING
1. Open the lamp as shown in Fig. 3.
2. Insert the power supply cable into the flexible membrane entry at the bottom of the base (see Fig. 4).
3. Mark the drill holes on the ceiling or wall and drill the holes the same size as the plugs provided.
4. Firmly press the plugs into the drill holes.
5. Attach the base against the ceiling or wall (see Fig. 4).
6. Connect the wires as shown in the wiring diagram in Fig. 6 (also see § 5).
7. Set the desired settings for the HF sensor (also see § 6).
8. Reattach the lampshade to the base and check that it is firmly in place (see Fig. 5).
5. WIRING
Connect the detector as shown in the wiring diagram in Fig. 6.
Conductor
Neutral conductor
Earthing
Output relay
The connected phase L' can be used for parallel connection of up to one similar additional load. It is recommended
to pass additional load through an external relay. A N.C. push button (to be ordered separately) can be connected
to switch the lighting off or on, taking into account the set switch-off delay (see Fig. 6a). You can also choose
to connect a switch (to be ordered separately) with which you can switch lighting on permanently (see Fig. 6b).
When you turn off the switch, the detector resumes its normal operation.
6. CONFIGURATION
6.1. Light sensitivity
Using the LUX potentiometer, you can set the threshold value of the twilight switch continuously between ð
(daytime mode, 2000 lux) and ƒ (night mode, 5 lux) (see Fig. 7c). In automatic mode, the light is only switched
on once the set threshold value is reached.
6.2. Switch-off delay
Using the TIME potentiometer, the switch-off delay is set between ±5 s to 5 min. (see Fig. 7a). The switch-off
delay determines the length of time the light stays on after the final movement in the detection area.
6.3. Detection range
Using the METER potentiometer, the detection range of the detector is set (approx. 1 – 8 m diameter) (see Fig. 7b).
7. TROUBLESHOOTING
Malfunction Solution
The light does not switch on. • The threshold value has not been reached. Increase the light sensitivity
• Increase the detection range using the METER potentiometer.
• Check the lighting and the fuse.
The light switches on without • The threshold value has been reached. Lower the light sensitivity
cause.
4
• Decrease the detection range using the METER potentiometer.
• Check the detection area for causes of incorrectly switching on
EN nv Niko sa Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu
352-02702 352-02703
alu black
L
N
(PE)
L'
using the LUX potentiometer (in the direction of ƒ).
using the LUX potentiometer (in the direction of ð).
(movement of plants, animals, etc.).
8. TECHNICAL DATA
Base colour
Dimensions in mm (LxW)
Dimensions in mm (H)
Lampshade material
Lamp type
Nominal power
Nominal voltage
Power factor
Brightness
Light efficiency
Colour temperature
Frequency range
Detection angle
Detection range
Mounting height
Light sensitivity
Switch-off delay
Protection class
Protection degree
IK rating
Ambient temperature
Marking
9. WARNINGS REGARDING INSTALLATION
• The installation should be carried out by a registered installer and in compliance with the statutory regulations.
• This user manual should be presented to the user. It should be included in the electrical installation file,
and it should be passed on to any new owners. Additional copies are available on the Niko website or via
the Niko support service.
• During installation, the following should be taken into account (non-exhaustive list):
- the statutory laws, standards and regulations.
- the technology currently available at the time of installation.
- this user manual, which only states general regulations and should therefore be read within the scope
of each specific installation.
- the rules of proper workmanship.
This product complies with all of the relevant European guidelines and regulations. If applicable, you can find
the EU declaration of conformity regarding this product at www.niko.eu.
10. NIKO SUPPORT
In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support
service in Belgium at +32 3 778 90 80 or your wholesaler/installer. Contact details and more information can
be found at www.niko.eu under the "Help and advice" section.
11. WARRANTY PROVISIONS
• The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of purchase
of the product by the consumer. If there is no invoice, the date of production applies.
• The consumer is obliged to inform Niko in writing about the non-conformity, within two months of noticing
the defect.
• In case of a non-conformity, the consumer only has the right to a product repair or replacement free of charge,
which shall be decided by Niko.
• Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless
use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance
instructions or an external cause, such as damage due to moisture or overvoltage.
• The compulsory regulations of the national legislation concerning the sale of consumer goods and the
protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries,
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and regulations.
Niko nv hereby declares that the types of radio equipment 351-02701, 351-02702 and 351-02703 comply
with Directive 1999/5/EC and Directive 2014/53/EU.
The full text of the EU Declaration of Conformity can be found on www.niko.eu.
This product cannot be deposited in the unsorted waste. Take your discarded product to a recycling centre or a recognised
collection point. Just like producers and importers, you too play an important role in the promotion of sorting, recycling
and reuse of waste electrical and electronic equipment. To finance the rubbish collection and waste treatment, the government
levies recycling charges in certain cases (included in the price of this product).
352-02701 352-02702
white alu
237 x 157
75
Aluminium/plastic
LED
13 W
230 – 240 V, 50/60 Hz
> 0.9
700 lm
54 lm/W
3000 K
5.8 GHz / 1 mW
360° with 160° angular aperture
Ø 1–8 m
2–5 m
5–2000 lux
5 s - 5 min.
Protection class I
IP65
IK10
-10 – 45 °C
CE marked
PM352-02701R16353
352-02703
black