Publicité
Les langues disponibles
Les langues disponibles
www.digisportinterntional.com
INSTRUCTION MANUAL
DT2000
FEATURES:
- Hour, minute, seconds, month, date, day
and alarm 12/24 hour and month/date or
date/month display user selectable
- 2000 memories
-
Segregated
memory
memorize LAP times of different races)
-
User
Selectable
LAP/SPLIT
LAP/SPEED display
- Average and best lap time display
- Automatic release of LAP time after 10
seconds to allow progress monitoring.
- Data can be printed by printer (DT 500P
optional) at operation or selectively by
race later
- Data can be uploaded to computer
through upload cable with software (cable
and software optional)
- Dual timers which start one after another
for use in training programs
- Can be used as ordinary countdown
timer if 2nd timer is not set
TIME SETTING
1.
Press C to go to the TIME MODE (fig 24).
2.
Press and hold B button will go into the
TIME SET mode with the AL HOUR
blinking.
3.
Press A to set the AL HOUR.
4.
Press B to select digits in the following
sequence: AL HR, AL MIN first digit, AL MIN
2nd digit, AL OFF/ON, YEAR last digit, YEAR
1st digit, MONTH, DATE, 12/24HR selection,
HOUR, MIN 1st digit, MIN 2nd digit, and
SECONDS.
5.
Press A to set the blinking digits.
6.
Pressing C any time during this setting
sequence will complete the setting procedure
and return to the normal TIME display. If
12HR option is selected the calendar will be
shown as MONTH/DATE/YEAR and time will
be displayed in 12 HOUR system. If 24HR
option is selected, the calendar will be
displayed as DATE/MONTH/YEAR and time
will be displayed in 24HOUR system. The
calendar automatically adjusts for weekday
and odd and even months including February
of leap years up to year 2089.
7.
Press D in the TIME mode to arm or
disarm the alarm. When the alarm is armed
the alarm indicator will be turned on and the
alarm will sound at the preset alarm time.
CHRONOGRAPH OPERATION:
1.
2.
1.
SPEED DISPLAY:
1. In the CHRONO MODE before the
start of a race, push and hold B for 2
seconds will go to the SPEED SET mode
(capability
to
as is shown in Fig.14.
or
2.
3.
4.
5.
6.
7.
8.
9.
Press
C
to
go
to
CHRONOGRAPH
MODE.
display as shown in Fig. 2.
Before start, choose your display
The first digit in the lowest row is
flashing to indicate setting of the
thousandth digit of distance.
Push A to set and B to select the
next digits. The highest setting for
distance is 9999.999.
After the digits are set press B again
to set the TIME unit with the top left
corner HR flashing.
Use A to set to HR (for /hour), MIN
(for /minute) or SEC (for /second).
When the distance and time unit are
set, press C button to return to the
SPEED MODE (Fig. 15). (Pushing
C button anytime during the setting
will return to the SPEED mode).
Press A to start, the display is as
shown in Fig.16.
Press B to get the 1st LAP time at
the top row and the speed at the
middle row, as shown in Fig.17.
If for example the distance is set to
200 meters and time unit set is in
seconds, the speed calculated from
a LAP time of 17.09 seconds is
11.70 m/sec. [Using the B button
the
LAP
times
and
corresponding
speeds
can
displayed. Recall operations in the
SPEED mode are the same as in
the LAP/SPLIT mode.]
2. SPLIT TIME DISPLAY:
the
The
1.
Press B to get the 1st LAP time.
The LAP time is shown at the top
row, the SPLIT time at the middle
row and the running total time is
shown at the lower row, as shown
in Fig.3.
3.
10 seconds later the display will
automatically be released to show
the running LAP and SPLIT times to
allow the user to keep track of
progress, as shown in Fig. 4.
4.
Press B to display the 2nd LAP
time.
5.
Press A to stop.
6.
Press B to reset and be ready for
the next race, as shown in Fig. 7.
The counter at the top left corner
displays the memory left for further
races.
7.
Further races can be recorded by
pressing A and B buttons as above.
8.
Since 5 memories are used for
memorizing the date and number of
the race, the memory left will be
1993 as shown below.
STROKE / FREQUENCE BASE 3 ;
a. Press the button C to go into
« chronograph mode ».
b. Press B during few seconds to go
into « speed mode » (in fig.14).
c. Scroll with the button B.
d.
Select the numbers with the button
A. The distance has to be set up
on « 180 » (0180.000) and the time
unit
Then, press C to confirm.
e.
Start the « chronograph mode »
with the button A. After the third
stroke only, press A again. The
line in the middle indicates the
number of strokes per minute.
their
be
on
« seconds »
(SEC).
Publicité
