Rockford Fosgate PMX-1 Mode D'emploi page 7

Source Unit Settings
To access the source unit's settings, press and hold the MENU button
until the options appear. Rotate the encoder to scroll through the list
of settings and press the encoder button to select the setting you
wish to change. (BALANCE>FADER>AUDIO>VOLTAGE GAUGE>BT
PAIRING>BEEP>TUNER REGION>SOFTWARE>FACTORY DEFAULT)
This source unit has a zero current draw when turned off. All of your
settings and presets will be saved along with your boat's battery during
storage.
BALANCE
Press the encoder button to access BALANCE adjustment settings. Rotate
the encoder button to set the output BALANCE.
FADER
Press the encoder button to access FADER adjustment settings. Rotate
the encoder button to set the output FADER.
AUDIO
To access the AUDIO settings, press the AUDIO option from the MENU
screen. Rotate the encoder to scroll through the list of settings and
press the encoder button to select the setting you wish to change.
(7 BAND EQ>CROSSOVER>PEQ>REAR RCA>AUX INPUT>SOURCE
GAIN>INTERNAL AMPLIFIER)
7 BAND EQ
Press the encoder button to access the 7 BAND EQ settings. Use
the rotary encoder to scroll through the EQ settings. (FLAT > ROCK
> CLASSIC > ACOUSTIC > DANCE > ELECTRONIC > HIP-HOP >
CUSTOM) When setting up the CUSTOM EQ, press the encoder button
to set the first frequency. Once active, rotate the encoder to adjust the
frequency settings. Press encoder button again to access the next
frequency. Repeat until all EQ settings are complete. Press the MENU
button to exit and go back up one level.
CROSSOVER
Press to access the CROSSOVER settings. Use the rotary encoder
to select the crossover zone options (FRONT>REAR>SUB).
Press the encoder to adjust the frequency of the crossover
(60Hz>80Hz>120Hz>APF). Press MENU to exit and go back up one level.
REAR RCA
Press to access the REAR RCA options. Use the rotary encoder to select
options (LINE OUT>SUBWOOFER).
PUNCH EQ
Press to access the PUNCH EQ settings. Use the rotary encoder to adjust
the gain output (0-12). Press MENU to exit and go back up one level.
Punch EQ is an onboard equalizer with up to +18dB @ 45Hz and/or up to
+12dB boost at 12.5kHz
AUX INPUT
RENAME – To rename AUX, press the encoder button to set the first letter
of the new name. Once active, rotate encoder to adjust letters. Press the
encoder button again to set the next letter. Repeat until AUX has been
renamed. Press MENU to exit and go back up one level.
ENABLE - Press the encoder button to access options. Rotate the encoder
button to select if unit is discoverable. (ENABLE > DISABLE)
SOURCE GAIN
To adjust the level of device input gain, scroll through the inputs (FM
TUNER>AM TUNER>WB TUNER>USB>AUX>BLUETOOTH) to the device
you want to adjust, press the encoder button to access the gain settings.
Rotate the encoder button to set the level of gain. (-3dB > -2dB > -1dB >
0dB > +1dB > +2dB > +3dB)
INTERNAL AMPLIFIER
Press to access the INTERNAL AMPLIFIER options. Use the rotary
encoder to select options (ON>OFF). When using an amplifier to power
your speakers, select OFF. If you are powering your speakers directly
from the source unit, select the INTERNAL AMPLIFIER to ON.
VOLTAGE GAUGE
To display the vehicle voltage, press the encoder button on the VOLTAGE
GAUGE option.
BT DEVICE PAIRING
Press the encoder button to access options (DISCOVERABLE > DEVICE).
DISCOVERABLE
Rotate the encoder button to select if unit is discoverable for pairing.
(ENABLE > DISABLE) Once enabled, the source unit is now discoverable
and ready for pairing to your device. Open the Bluetooth settings on your
device to find the source unit labeled "Rockford PMX" and select.
DEVICE
Selecting DEVICE by pressing the encoder button will allow you to
rename the source unit with up to 16 characters. This gives you the
ability to have a unique name for easy identification during device
pairing. Press the encoder button to select the letter to be changed and
rotate the knob to change the value. Repeat process until desired name
is reached.
BEEP
Press the encoder button to access the BEEP options. Rotate the encoder
button to turn system beep ON/ OFF.
TUNER REGION
To adjust, press the encoder button to access. Rotate the encoder button
to select the TUNER REGION of your preference. (EUROPE > USA >
RUSSIA > LATIN > ASIA > JAPAN > MIDEAST > AUSTRALIA)
CONTRAST RATE
To adjust the CONTRAST RATE, press the encoder to access the feature.
Rotate the encoder button to select the desired amount of contrast to be
displayed (1-10)
BRIGHTNESS
To adjust the BRIGHTNESS of the display, press the encoder to access
the feature. Click the encoder to select dimmer low then rotate the en-
coder to select the desired low brightness (1-10). Press encoder to lock
it in then roate the encoder to select dimmer high. Press on dimmer high
and select the desired high brightness (1-10) by rotating then pressing
the encoder once more to lock in the value. Now when the bottom left
dimmer button of the source unit is pressed, it will toggle the display
between the dimmer low value set and the dimmer high value set.
7
Settings