Before Installing; Cautions Regarding Handling - SYNQ CAX.1 Mode D'emploi

INSTALLATION MANUAL
INSTALLATION MANUAL
INTRODUCTION
Congratulations and thank you for buying this SYNQ product. Please read these
instructions carefully so you will know how to install this product properly. After you have
finished reading the instructions, put them in a safe place for future reference.

BEFORE INSTALLING

Check that the following parts are included in the package:
• Scratch Processor
• Special coded vinyl Scratch Record (supplied in a separate carton sleeve)
• AC/DC power supply
• 2 stereo jack/jack 3.5mm stereo cables
• Installation manual

CAUTIONS REGARDING HANDLING

SAFETY INSTRUCTIONS:
CAUTION: To reduce the risk of electric shock, do
CAUTION
not remove any cover. No user-serviceable parts
inside.
personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is
intended to alert the use or the presence of un-insulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute a
risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user
to the presence of important operation and maintenance (servicing) instructions
in the literature accompanying this appliance.
To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
Do not place metal objects or spill liquid inside the unit. Electric shock or malfunction may
result.
INSTALLATION GUIDELINES:
• Placing and using the unit for long periods near heat-generating sources such as
amplifiers, spotlights, etc. will affect its performance and may even damage the unit.
• When installed in a booth or flight case, please make sure to have good ventilation to
improve heat evacuation of the unit.
• To avoid condensation to be formed inside, allow the unit to adapt to the surrounding
temperatures when bringing it into a warm room after transport. Condense sometimes
prevents the unit from working at full performance.
• Choose the place where you put your installation very carefully. Avoid presence of
heat sources. Avoid places with vibrations or places that are dusty and humid.
• To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
SYNQ 1/20
ENGLISH
Refer servicing to qualified service
CDX-1 SCRATCH PROCESSOR
INSTALLATION MANUAL
• In order to prevent electric shock, do not open the top cover. If a problem occurs,
contact your dealer.
• Do not place metal objects or spill liquid inside the unit. Electric shock or malfunction
may result.
• This unit may cause interference to radio and television reception.
PARTS OF THE UNIT
1. PHONO INPUT: This is a normal phono input. Connect the cinch cable coming from a
turntable to this input.
Important: this input only accepts phono level signals. If your turntable has a phono/line switch, be
sure to switch it to phono. With line level signals the scratch processor will not work properly and can
even be damaged.
2. PHONO GROUND: If your turntable has a ground connector, we strongly suggest
connecting it to this input. This avoids hum and pops associated to the low signal
levels of phono cartridges.
3. CLOCK OUT1: This output is used to send the control signals from the Scratch
Processor to the CDX-1 CD-player. Connect one of the supplied 3.5mm stereo
jack/jack cables between this output and the left Scratch Processor input on the back
of the main unit. This output only works when the specially coded scratch record is
used on the turntable.
Important: Only use the supplied 3.5mm stereo jack/jack cables! Don't mix these cables with the
3.5mm mono jack/jack fader start cables supplied with CDX-1 CD-player!!!
Using mono jacks may permanently damage the Scratch Processor and voids all warranties.
4. CLOCK OUT2: This output is used to send the control signals from the Scratch
Processor to the CDX-1 CD-player. Connect one of the supplied 3.5mm stereo
jack/jack cables between this output and the right Scratch Processor input on the back
of the main unit. This output only works when the specially coded scratch record is
used on the turntable.
Important: Only use the supplied 3.5mm stereo jack/jack cables! Don't mix these cables with the
3.5mm mono jack/jack fader start cables supplied with CDX-1 CD-player!!!
Using mono jacks may permanently damage the Scratch Processor and voids all warranties.
5. POWER SUPPLY INPUT: connect the supplied 9Vdc power supply to this input.
6. PHONO OUTPUTS: Connect these outputs to the phono inputs of your mixer. This
output is switched off when you put the special scratch record on the turntable. While
playing an ordinary analog vinyl record, this output sends the music to the phono input
of the mixer. To prevent hum, don't forget to connect the GND-cable to the mixer.
SYNQ 2/20
ENGLISH
CDX-1 SCRATCH PROCESSOR