Conrad Albir Mode D'emploi page 3

O P E R A T I N G I N S T R U C T I O N S
Recessed LED light "Albir", 2.5 W
Item no. 55 95 50
Intended use
The product is intended for illuminating indoor areas; it may only be installed and used in dry,
enclosed indoor rooms. The product is intended for installation in suspended ceilings.
The safety instructions must be observed at all times!
Any use other than that described above could lead to damage to this product and involves the
risk of short circuits, fi re, electric shock, etc.
This product complies with the applicable national and European requirements. All names
of companies and products are the trademarks of the respective owners. All rights reserved.
Package content
• Recessed light
• Connection cable
• Operating instructions
Explanation of Symbols, Inscriptions
This symbol indicates specifi c risks associated with handling, function and use.
The "Hand" symbol indicates special tips and operating information.
The product is intended to be located and used only in dry indoor spaces; it must not
get damp or wet.
Do not embed the light in the insulating material during installation and subse-
quent use, as this may lead to overheating of the light. Furthermore, there is a
fi re hazard!
Keep a minimum clearance between the light outlet and the illuminated areas
0.2m
(e.g., easily fl ammable objects such as curtains or the like). The appropriate
minimum distance is specifi ed on the bulb (in the illustration to the left, the
minimum distance is 0.2 m).
Symbol for protection class III
Observe the operating instructions!
Safety Instructions
Read the complete operating manual carefully before using the product, as it
contains important information about the proper installation and operation.
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any resulting
damage!
We shall not accept liability for damage to property or personal injury caused
by incorrect handling or non-compliance with the safety instructions! The
warranty will be void in such cases!
If you do not have the expertise required for the installation, do not install it
yourself but entrust the work to a qualifi ed electrician.
• Unauthorised conversion and/or modifi cation of the product is not allowed for
safety and approval reasons (CE).
• The product is not a toy and does not belong in the hands of children! Install the
product out of the reach of children.
• The product is designed according to protection class III.
• The LED light may be operated only by a constant current source; use a suitable
ballast (LED driver). Refer to the chapter "Technical Data".
Operation with commercially available halogen transformers, power supply units
or the like is not possible, this destroys the light, loss of guarantee!
• The LED light may only be installed and used in dry indoor rooms, it must not
become damp or wet.
• Only use the lamp when it is permanently mounted.
• Do not use this light in rooms that are under adverse ambient conditions where
combustible gases, vapours or dust are or may be present! There is a risk of explo-
sion!
• Do not hang or attach objects (e.g. decorative material) to the light, there is a risk
of fi re!
www.conrad.com
Version 07/13
Preparations for Installation
• Install the LED light only on a stable base, e.g. in a dropped interior ceiling (e.g. ceiling
panel).
• The light is only intended to be placed and used in dry indoor rooms, it must not become
damp or wet.
• Do not install the light in or on surfaces that are highly fl ammable or catch fi re easily.
• Keep suffi cient distance between the light-emitting opening of the light and the exposed
surfaces, otherwise this may result in discolouration of the exposed surface. Furthermore,
there is a fi re hazard.
• The LED light may not be embedded in the insulating material, as this may cause overheating
of the light. This will not only lead to a reduced operating life but it also constitutes a risk of
fi re! We recommend a minimum distance of 10 cm.
• The light must be installed and used out of the reach of children.
• Installation and connection of the LED light may be done only in the absence of any voltage.
• Caution, LED light:
Do not look directly into the LED light!
Do not look into the beam directly or with optical instruments!
• The product must not be exposed to extreme temperatures, strong vibrations or
heavy mechanical stress.
• If it can be assumed that safe operation is no longer possible, the device must be
turned off and precautions must be taken to ensure that it is not used unintention-
ally. After this, arrange for an expert to check the product.
Safe operation can no longer be assumed if:
- the product shows visible signs of damage
- the product does not work at all or works poorly (where there is fl ickering light,
leaking smoke or a smell of burning, audible crackling noises, or discolouration
of the product or to adjacent surfaces)
- the product was stored under unfavourable conditions
- it was exposed to heavy loads during transport
• Do not leave packaging material carelessly lying around, since it could become a
dangerous plaything for children.
• In commercial institutions, the accident prevention regulations of the Employer's
Liability Insurance Association for Electrical Systems and Operating Facilities are
to be observed.
• If you have any questions that are not answered in this manual, please contact our
technical service or another specialist.
Please consult the chapter "Safety Instructions"!
The LED light may be operated only by a constant current source; use a suitable
ballast (LED driver). Refer to the chapter "Technical Data".
The LED light may not be attached to a commercially available halogen transformer;
this will damage the LED light, loss of guarantee!