TESY LightModel GM 4.7 Notice D'utilisation page 19

V. CONTROL VIA THE INTERNET
��
/
/QUICK START
Note: If upon activation of the mobile application the main menu of
the electric water heater is loaded, and not the dedicated screen for
control via the Internet, you need to stop the direct Wi-Fi connection with
the appliance established through its aerial wireless network
TCHxxxxxxxx.
Working with the screen to control the device via the Internet
1. To make any settings the water heater should be switched on:
2. Manual operation mode
Manually set the desired hot water quantity using the slider. During heating
the message "HEATING" will appear on the screen and the current state will be
shown in red colour.
When the appliance has reached the set value the message "READY" will appear
on the screen and the current state will be shown in dark purple colour.
Weekly programmer mode P1 , P2 and P3
3.
To see the time schedule of each programme and to change it, if needed, press
the status bar or the icon and select one of the three programme modes.
4. Eco mode , ,
In Eco mode the electric heater elaborates its own algorithm for operation so as
to ensure energy saving, and therefore, to reduce your electricity bill and at the
same time to keep the comfort in your home while it is being used.
5. BOOST function or
When the BOOST function is enabled the water heater will heat the water
up to maximum possible temperature of without changing the algorithm
of operation of the respective mode of operation, i.e. without changing the
weekly programme, the Eco Smart logics of operation or the manually set
temperature.
TROUBLESHOOTING
If you have any problems with your water heater, please contact the service which is add in the warranty card or the dealer from which you have bought the device.
Most frequent problems:
Failed connection to or finding of the Wi-Fi network of the appliance
Failed connection to the home Wi-Fi network
(wireless connection)
The water heater cannot be seen in the application.
The water heater is connected correctly, but it does not work
If the inbuilt wireless module does not find the wireless router
(modem)
After I have connected to the Wi-Fi network of the appliance, I do not
see it in the browser window
You have forgotten the password of the wireless Wi-Fi device of the
water heater.
An attempt to restore the factory settings fails.
Upon opening the mobile application, the main menu is visualized in
the water heater's network
English
6. Vacation mode
If you plan to be away from home for more than 1 day, you can enable the
Vacation mode so that the electric water heater will "know" when you will be
back to provide you with hot water.
7. Calculating the consumed power over a period of time
Using the embedded calculator for consumed power
energy costs for a specific period of time.
8. Activity over past 24 hours.
9. GROUPING function
There is an opportunity to simultaneously control a group of appliances.
The grouping of appliances is done by selecting the icon
10. Removing the GROUPING function:
Select the button and the symbol
group.
Date and time setting.
Shower symbol
The Handset symbol
water that has already been heated. The quantity of water has been calculated
on the basis of average European norms and it may not coincide with your
personal preferences for comfort.
For full instructions for use and store, follow thе link below:
TESY's team reserves the possibility to change and add new functions in the
products with inbuilt Wi-Fi module, as well as to change the instructions in
accordance with the new versions of the software.
Solution:
Check whether the wireless connection symbol on the display is active.
Check whether the appliance is connected to the power supply source.
Get close to the appliance.
Check whether the modem is on.
If you use a laptop, make sure that the switch for the wireless connection, located in the
front, the side or the back of the laptop is in ON position
Make sure that you have entered correctly the name of your home network.
Wait for about 1 minute and check again whether the connection is successful.
Check whether your router is connected to the Internet.
The appliance has to be connected to the wireless router (modem) in your house (of-
fice).
Check whether you have entered correctly the email of your account in the main menu
of the appliance's network.
Restart the application.
Use an additional wireless module to enhance the signal of the wireless router
(modem).
Enter the address 10.0.0.1 in the address bar of the browser and you will see the
application.
If you have forgotten the password for protection of your network, you will need to use
the RESET function of the appliance to restore its factory settings. See Instruction for
use and storage, Restore Factory Settings section.
The appliance has to be switched off from the stand-by button (it has to be illuminated in white).
If upon activation of the mobile application the main menu of the water heater is loaded,
and not the dedicated screen for control via the Internet, you need to stop the direct
Wi-Fi connection with the appliance established through its aerial wireless network
TCHxxxxxxxx and then connect to your home network.
you can track the
appears next to each appliance in the
provides you with information on the amount of hot
https://tesy.com.
EN
.
19