How To Use - IRIS BLW-C2 Serie Mode D'emploi

HOW TO USE

Please make sure the blanket the product is being used on can withstand temperatures higher
CAUTIONS
than 158°F/70°C . The warm air temperature may cause damage to the performance
of the blanket, such as low repulsion, pilling, etc .
Dry Blanket / Warm Blanket / Eliminate Dust Mites
Blanket Size Indication (This product can warm sheets and blankets together .)
Twin / Full
• Mattress: 39 .4-82 .7 in/100-210 cm (6 .6 lbs ./3 kg)
• Blanket: 59 . 1 -82 .7 in/150-210 cm (6 .6 lbs ./3 kg)
1. Unfold the hose and open the air flap at the hose tip until it is
locked into place, then place the product on the blanket with the
operation panel facing upwards.
About the Air Flap:
You can expand the coverage of warm air by making space under the
blanket .
CAUTIONS
• Fully stretch out the hose .
• This product will stop operating if it is laid down with the air
entry port on the right side facing down .
• Ventilate the room frequently as moisture is released from
the blanket .
• Keep the side air entry port at least 6 in/15 cm from the
wall .
• Place a large towel between the blanket and floor before
drying or warming . (Condensation may occur due to the
moisture between the floor and blanket) .
2. Warm the blanket.
Insert the edge of the blanket into the space between the main body
and hose .
*Please do not pull the blanket by force, otherwise it may cause
damage to the blanket and air flap .
Hold down firmly to prevent air leakage between the hose and blanket .
CAUTIONS
• Please do not place the blanket on the main body or block
the air entry ports .
• The non-overlapped area between the mattress and blanket
may not heat sufficiently .
• This product cannot solely dry a mattress . Make sure to
place the blanket on the hose before use .
Queen / King
• Mattress: 55 . 1 -82 .7 in /140-210 cm (8 .8 lbs ./4 kg)
• Blanket: 74 .8-82 .7 in /190-210 cm (8 .8 lbs ./4 kg)
Hose tip Air flap
Open
Body Blanket
Insert here
Air entry port
7
3. Insert the power plug securely into the electric socket.
In standby mode, press any key to light up the power indicator, and it will
then enter mode selection .
4. Select automatic warming mode.
Press the MODE button to select desired mode .
PRESET FUNCTIONS
WINTER (High temperature air 60 minutes)
WINTER SUMMER
SUMMER (High temperature air 60 minutes + air blast 20 minutes)
WARM UP Dust Mite Eliminator
WARM UP (High temperature air 20 minutes)
MODE
Dust Mite Eliminator (High temperature air 100 minutes)
5. Press START/ON button.
This product will display the remaining time after it starts running . It will
stop heating after set time has run out, and then it will cool down the main
body and hose with a 20 second air blast before it stops running .
• During and immediately following use, do not use the blanket or allow
pets on the blanket . Doing so may cause burns .
• Do not unplug the power plug while product is running .
• Press the CLEAR/OFF button if you want to stop warming . Product
will stop warming and will blast air for 20 seconds, and then the
product will stop running .
• The power indicator will turn off 5 minutes after use .
• If the warmer does not warm the whole length of the blanket or does
not reach the corners, please insert the hose on the other side of the
blanket and run the product again .
*It is more efficient to use a mattress cleaner after dust mite elimination .
6. Put the product away after use.
• Firmly grip the power plug to unplug it from the electric socket .
• Close the air flap and fold the hose .
Fold
• Bundle up the power cord .
TIME MINS POWER SUPPLY
SETTINGS
PRESET FUNCTIONS
TEMPERATURE CLEAR/OFF
WINTER SUMMER
WARM UP Dust Mite Eliminator
TIMER START/ON
MODE
(Front)
START/ON
Bend
Press
gently
Power cord
to store
hose
TIME MINS
POWER SUPPLY
SETTINGS
PRESET FUNCTIONS
TEMPERATURE CLEAR/OFF
WINTER SUMMER
WARM UP Dust Mite Eliminator
TIMER START/ON
MODE
(Back)
8
Cover