General Safety; Product Familiarisation - Silverline 999666 Traduction Des Instructions Originales

999666

General Safety

WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and
Carefully read and understand this manual and any label attached to the tool before use. Keep these
instructions with the product for future reference. Ensure all persons who use this product are fully
acquainted with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk factors. Use with
caution. If you are at all unsure of the correct and safe manner in which to use this tool, do not
attempt to use it.
Work area safety
a) Do not operate electrical devices in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Electrical devices create sparks which may ignite the dust or
fumes.
Electrical safety
a) Electrical plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) devices. Unmodified plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose non-waterproof electrical devices to rain or wet conditions. Do not
submerge non-pressure-rated devices in water. Water entering an electrical device will
increase the risk of electric shock.
d) Do not abuse the power lead. Never use the lead for carrying, pulling or unplugging the
device. Keep lead away from heat, oil, sharp edges or moving parts. Damaged or entangled
power leads increase the risk of electric shock.
e) If operating an electrical device in a damp location is unavoidable, use a residual current
device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
WARNING: When used in Australia or New Zealand, it is recommended that devices are ALWAYS
supplied via Residual Current Device (RCD) with a rated residual current of 30mA or less.
Personal safety
a) Stay alert, watch what you are doing and use common sense when operating an electrical
device. Do not use potentially dangerous electrical devices while you are tired or under
the influence of drugs, alcohol or medication. A moment of inattention while operating
potentially dangerous devices may result in serious personal injury.
b) Use personal protective equipment including eye protection where appropriate. Protective
equipment used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting
to a power source. Carrying electrical devices with your finger on the switch or energising
devices that have the switch on invites accidents.
d) Do not overreach. Keep proper footing and balance at all times. This enables better control
of the device in unexpected situations.
Use and Care
a) Do not force the device. Use the correct device for your application. The correct device will do
the job better and safer at the rate for which it was designed.
b) Do not use the electrical device if the switch does not turn it on and off. Any device that
cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the power source before making any adjustments, changing accessories, or
storing electrical devices. Such preventive safety measures reduce the risk of starting the
device accidentally.
d) Store idle devices out of the reach of children and do not allow persons unfamiliar with
the device or these instructions to operate it. Electrical devices may be dangerous in the
hands of untrained users.
e) Maintain electrical devices. Check for defects of parts and any other condition that may
affect the device's operation. If damaged, have the device repaired before use. Many
accidents are caused by poorly maintained electrical devices.
f) Use the device and its accessories in accordance with these instructions, taking into
account the conditions and the task to be performed. Use of the device for operations
different from those intended could result in a hazardous situation.
Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained
Battery & Battery Charger
Note: This product features a non-replaceable captive battery. The following is general safety
guidance for charging.
Use the battery charger correctly
• Refer to the section of this manual relating to use of the battery charger before attempting to
charge the battery
• Do not attempt to use the charger with any batteries other than those supplied. Keep the battery
charger clean; foreign objects or dirt may cause a short or block air vents. Failure to follow these
instructions may cause overheating or fire
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard
WARNING: Do not recharge non-rechargeable batteries
Use batteries correctly
• Only charge batteries using the charger provided. Only use batteries provided with this power
tool, or others recommended by the supplier. Keep batteries clean; foreign objects or dirt may
cause a short. Allow batteries to cool for 15 minutes after charging or heavy use. Failure to follow
these instructions may cause overheating or fire
• When not in use batteries should be stored at room temperature (approx 20˚C). Ensure that
batteries cannot accidentally short in storage.
Torch Safety
When the torch is switched on, the following must be observed:
• Do not look directly into the lens
• Do not shine into a person's eyes or an animal's eyes
• Do not point the beam at: cars, motorcycles, aircraft, ships or any other vehicle or machinery that
is operated by a person. Bright light can be blinding and you could cause a serious accident

Product Familiarisation

1 Bulb
2 Lens Ring
3 Handle Lock Button
4 Pistol Handle
5 On/Off Switch
6 Mains Charger
7 12v Charger
8 Adjustable D-Stand/ Handle
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features and
functions
• Ensure that all parts of the tool are present and in good condition.
If any parts are missing or damaged, have such parts replaced before attempting to use this tool
Before Use
IMPORTANT: The sealed lead acid battery in this product will be drained from storage. The following
steps must be taken to ensure it is charged correctly. This will maximise the performance and
working life of
the battery:
• Press the On/Off Switch (5) and check to see when the torch is On
• NOW MAKE SURE the product is switched OFF. The torch will only charge in the OFF position
• Plug the Mains Charger (6) in to the mains power supply, and plug the small end into the
charging socket
• Leave to charge for a MINIMUM of 16 hours before first use
NOTE: If the torch fails to charge repeat the above, ensuring that the Switch (5) is in the OFF
position.
silverlinetools.com
Rechargeable Torch
5