Princeton Tec QUAD TACTICAL MPLS Notice D'utilisation Et D'entretien

QUAD TM TACTICAL
MPLS
Operating and Maintenance
Instructions
Notice d'utilisation et d'entretien
Bedienungsanleitung
Battery Installation – See Battery Installation Diagram
• 3 AAA
• Alkaline (LR03)
• Rechargeable NiCad or NiMH
Princeton Tec cares about the environment and
recommends recycling batteries. For more information
about battery recycling, please go to:
www.batteryrecycling.com
Observe proper battery polarity when installing the
batteries. Improper installation of the batteries will
damage the light and void the warranty.
WARNING
• Never mix fresh and used batteries.
• Never mix different battery brands or chemistry types.
• Always remove drained batteries immediately.
• Remove batteries during long periods of storage.
NOTE: Lithium batteries offer extended constant
brightness time, extreme cold weather performance, and
lighter weight. Rechargeable NiCad or NiMH batteries
may result in reduced brightness due to lower nominal
voltage.
The Quad battery compartment has a waterproof seal. It
is important to keep this seal free from dirt and away from
harsh chemicals in order to preserve waterproof integrity.
Inspect the seal every time batteries are changed. If dirt
is present, wipe gently. With a damp cotton swab and
mild soap until dirt is removed.
NOTE: Some battery types can emit hydrogen gas, which
can create an explosion potential in sealed devices if it is
not vented or removed. The Quad is equipped with a
platinum catalyst to remove this gas. Upon severe
impact, the catalyst could fracture. If you notice a rattling
sound in the headlamp or gray particles in the battery
compartment, do not use the headlamp. See the
warranty and return policy for more information.
Switch Operation – See Switch Operation diagram
Modes (High, medium and low) are selected by pressing
and releasing the button within 1.5 seconds of the
previous button press.
There are two ways to turn the Tactical Quad off. You can
cycle through the modes until you reach off or if more
than two seconds has passed since the previous button
press the next press of the button will turn the light off.
**The times listed on the rear of the package assume you
have start with fresh batteries and use only one mode.
NVG Mounting System
To attach the MPLS Headlamp to the NVG Shroud:
1. Slide the bracket arm into the NVG Shroud adapter
plate, making sure the pull tab is above the lip of the
adapter plate and that the male grooves on the bottom of
the bracket arm are aligned inside the female grooves on
the bottom of the adapter plate.
2. Push the bracket arm securely into place, ensuring
that the pull tab audibly clicks over the lip of the NVG
Shroud adapter plate.
3. Your MPLS Headlamp should now be secured in the
NVG Shroud. You can rotate the headlamp to focus your
light source accordingly.
To remove the MPLS headlamp from the NVG Shroud:
1. Remove the NVG Mount from your helmet.
NVG Mounting System
0818
2. Push up slightly on the bottom of the light housing.
3. While pushing upward, use the tool on the provided
headstrap to press the tab of the arm bracket towards the
headlamp housing, so that it disengages from the NVG
Shroud adapter plate.
4. Slide the headlamp unit out of the NVG Shroud adapter
plate.
To attach the MPLS Headlamp to the Butterfly Mount:
1. Slide the bracket arm into the Butterfly Mount, making
sure the pull tab is above the lip of the mount and that the
male grooves on the bottom of the bracket arm are aligned
inside the female grooves on the bottom of the mount.
2. Push the bracket arm securely into place, ensuring that
the pull tab audibly clicks over the lip of the Butterfly Mount.
3. Your MPLS Headlamp should now be secured in the
Butterfly Mount. The mount can be attached to the provided
headstrap, MOLLE straps, or any 1" webbing. You can
rotate the headlamp to focus your light source accordingly.
To remove the MPLS headlamp from the Butterfly Mount:
1. Push up slightly on the bottom of the light housing.
2. While pushing upward, use the tool on the provided
headstrap to press the tab of the arm bracket towards the
headlamp housing, so that it disengages from the
Butterfly Mount.
3. Slide the headlamp unit out of the Butterfly Mount.
Troubleshooting
If the Quad Tactical fails to light:
• Check the batteries for proper installation.
• Replace batteries if proper installation is confirmed.
• Check the light for water contamination on the circuit
board. The light will resume normal operation once the
water is shaken or blown out and the light is left open until
completely dry. If the light has been contaminated with
salt water, flush the unit with fresh water and dry as
described above.
USA– International 5-Year Warranty
WARRANTY – Princeton Tec warrants this product to be
free from defects in workmanship and materials under
normal use for as long as you own this product. This
warranty covers all of the component parts of the product
Système de montage NVG
10
108
17
except batteries. This warranty does not cover deterioration
due to normal wear or damage due to misuse, alteration,
negligence, accidents, or unauthorized repair. Princeton Tec
will repair or replace parts which are defective in
workmanship or materials.
Your authorized Princeton Tec Dealer and Princeton Tec are
the only facilities authorized to repair the product. After (3)
unsuccessful attempts (within the warranty period) to repair
the product, you have the right to elect replacement of the
product or a refund of the purchase price less allowance for
use of the product. NO INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARE INCLUDED IN THIS WARRANTY. (Some
states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or
exclusions may not apply to you.) This warranty gives you
specific legal rights, and you may also have other rights
which vary from state to state.
Princeton Tec reserves the right to change product
specifications without notice.
FOR CALIFORNIA RESIDENTS
WARNING: This product contains Bisphenol A (BpA) a
chemical known to the State of California to cause birth
defects or other reproductive harm.
Return Policy
If your light fails to operate, follow these simple steps:
1. Check batteries. Replace if necessary.
2. To send your light in for repair or replacement, first contact
Princeton Tec customer service at 1-800-257-9080 to
request an RMA number. Please have your light model, date
of purchase and a brief description of the fault your are
experiencing. No warranty repairs will be accepted without
an RMA number.
3. Return the light to:
Princeton Tec, PO Box 8057 Trenton NJ 08650. Postage
due and freight collect items will not be accepted.
4. Upon receipt your light will be processed in about two
weeks. Please allow additional time for return transportation
from NJ.
Princeton Tec
PO Box 8057,
Trenton, NJ 08650
Phone: 609-298-9331
Fax: 609-298-9601
www.princetontec.com
© 2018 Princeton Tec
NVG-Befestigungssystem
5
80
92
24 50