Imperial VECTRA Série Guide D'installation Et D'utilisation

INSTALLATION AND OWNERS GUIDE
VECTRA SERIES
IMPORTANT SAFETY INSTRUCTIONS
WARNING – ALWAYS DISCONNECT THE UNIT
BEFORE PERFORMING MAINTENANCE OR
MAKING ANY CONNECTIONS. FAILURE TO
DISCONNECT POWER COULD RESULT IN ELECTRICAL
SHOCK OR DAMAGE, TO THE WALL CONTROL OR THE
ELECTRONIC COMPONENTS. IT IS RECOMMENDED
TO WEAR SAFETY GLASSES AND GLOVES WHILE
PERFORMING THESE INSTRUCTIONS.
CAUTION – FOLLOW THE INSTRUCTION TO INSURE
PROPER OPERATION AND FUNCTIONALITY OF THE
CONTROL AND VENTILATION SYSTEM. – ONLY
ONE WALL CONTROL PER VENTILATION SYSTEM IS
POSSIBLE - KEEP WALL CONTROL LOW VOLTAGE WIRES
MINIMUM 2FEET(610MM) AWAY FROM MOTORS, LIGHT
BALLAST, DIMMERS AND ELECTRICAL PANELS – DO
NOT ROUTE WALL CONTROL LOW VOLTAGE WIRES
ALONG SIDE HIGH VOLTAGE WIRES – MINIMUM WIRE
REQUIREMENTS: LVT 18/4 CSA/UL. – THE DEFINED
MAXIMUM LENGTH FOR THE WIRE CONNECTION IS
VENTILATION
250 FT (MAX).
ECONO
VENT
MOUNTING THE VECTRA SERIES WALL
20 MIN/HR
CONTROLS (EHC 1.0 TC AND EHC 1.5 DC)
OFF
1) Unplug the ventilation system from main power source.
2) Installation with a single electrical junction box. Find a suitable
location for the wall control that is free of obstructions. Using
the electrical junction box, outline the box on the wall. Proceed
ON/OFF PREF
to cut out the opening outlined on the wall.
3) Once the hole in the drywall is cut out, enter the wall control
routed wires from the unit through the circular opening of the
electrical junction box and push into place. Note: Always secure
the junction box to a wall stud or by using electrical junction box
side brackets. With a screw driver, secure the wall control wires
to the electrical junction box with the built in clamp.
Note: The wall control can also be installed without using a
electrical junction box, by simply cutting a 2-7/8" by 1-1/3"
at the desired location and securing it to the wall with wall
anchors.(included)
4) Remove the insulation covering the end of the wire to expose
the 4 wires, then strip the end of each individual wire. With
a screw driver connect each wire on the back of the control
switch to its corresponding terminal. RED wire to "R" / BLACK
wire to "B1" / GREEN wire to "G" and WHITE wire to "W". (Ref
to figure 1.0)
5) Mount the wall control and install the Decora® wall plate.
6) Plug the ventilation system and proceed to test the wall control
operation.
Wall Plate Control Junction Box
Switch
Fig. 1.0 Wiring diagram
Plaque Commande Boîte
Control Switch Ventilation System
murale murale de jonction
N.C. N.O.
RLY1
INTERLOCK
D1
SW3
R
B1
G
B1
W
Imperial Manufacturing Group
40, Industrial Park St.
Richibucto, NB Canada E4W 4A4
www.imperialgroup.ca
PR0776 / SEP2016
VENTILATION
ON/OFF
OFF
VENT
RECIRC
20 MIN/HR
Wall
2 1 / "
4
POWER ON/OFF WALL CONTROL
- Press and hold the
3 1 / "
4 "ON" the wall control.
Note: The factory default values are: "VENT MODE / MED
SPEED"
- Press and hold the
"OFF" the wall control.
VENTILATION MODE SELECTION
- Press the
Mur
ventilation operating mode.
- Press the
COM
2 1 / po
4
B G R modes: VENT - 20MIN/HR – RECIRC or RECIRC-20 MIN/HR
TIMER
the selected ventilation mode value will flash.
+ J2
- Press the
–
MASTER
3 1 / po The wall control will automatically go to "SPEED SELECTION"
4
REMOTE SPEED SELECTION
W B G R
The speed selection menu for the operating speed is now
activated and is identified by
- Press the
speeds: MAX/MED or MIN, the selected speed value will flash.
- Press the
control will automatically go to "ECONO MODE".
POWER FAILURE:
After a power failure, the wall control returns to its original selected operating mode. All settings are kept in memory.
WALL CONTROL COMPATIBILITY
Due to constant product evolution and updated technologies, some wall controls are not compatible with earlier ventilation system
models. For more details please contact our technical support line at 888.724.5211 our via e-mail customerservice@imperialgroup.ca.
ECONO
VENT
20 MIN/HR
OFF
PREF
OPERATING THE
VECTRA EHC 1.0 TC
WALL CONTROL
MAX
MED
MIN
SUMMER/ÉTÉ
88 %
OPERATING THE
VECTRA EHC 1.5 DC
WALL CONTROL
= Continuous ventilation mode maximizes
your indoor air quality
= Friendly continuous ventilation energy
savings mode
= Recirculation ventilation mode (compatible
with SS3.12 DD, DH 7.15 and XDH 7.15 only)
= 20 min continuous ventilation /
40 min intermittent (standby) mode
= 20 min continuous ventilation /
40 min recirculation mode
= Humidistat override mode
= Maximum ventilation speed
= Medium ventilation speed
= Minimum ventilation speed
= The ventilation system is powered OFF.
(puts the unit in stand-by mode), it will
respond to override controls. (If present)
OK button for 3 seconds to power
button for 3 seconds to power
OK
OK button to enable the selection menu for the
or button to select the ventilation
s t
OK button to select the desired ventilation mode.
.
or button to select the ventilation
s
t
OK button to select the desired speed. The wall
POWER ON/OFF WALL CONTROL
Press the button powers the wall control ON or OFF
Note: The default mode when powered ON is "VENT"
VENTILATION MODE SELECTION
Press the button is the ventilation mode selector for your
MAX
MED
ventilation system, when the control is powered ON,
MIN
OFF SUMMER/ÉTÉ
VENT 88 %
RECIRC
= Friendly continuous ventilation energy savings
20 MIN/HR
mode
= Continuous ventilation mode maximizes your
indoor air quality
= 20 min maximum speed / 40 min intermittent
(the ventilation system is in stand-by mode)
= The ventilation system is powered OFF. (puts the
unit in stand-by mode), it will respond to override
controls. (If present)
ECONO MODE
The econo mode is now activated and is identified by
- Press the or button to enable or disable the
s t
ECONO mode option, the selected
- Press the button to select the desired econo mode.
OK
The wall control returns to the selected operating mode.
RECIRCULATION MODE
(Only available on selected models)
To enable or disable the RECIRC mode option.
- Press and hold simultaneously the
buttons for 3 seconds will enable the RECIRC mode feature
and is identified by .
- Press the or button to enable or disable the
s t
RECIRC mode, the selected RECIRC value will flash.
- Press the OK button to select the desired RECIRC mode.
(RECIRC only compatible with C 3.14, RNC 1.0 and XDH 7.15
models.) The wall control returns to the selected operating mode.
SETTING THE RELATIVE HUMIDTY (RH) LEVEL.
Setting the relative humidity (RH) for the desired indoor humidity
level (in percentage). This value will be used to boost the
ventilation system to maximum speed based on the measured
indoor relative humidity value.
- Press and hold simultaneously the
to for 3 seconds. The relative humidity percentage value will
flash. (Default setting = 80%).
- Press the or button to change the value. (Value
s
t
changes by 1% increments). Lower value 20%/Higher value 80%.
- Press the button to select the desired relative humidity
OK
(RH). The wall control will automatically go to "SUMMER MODE".
IMPORTANT:: = Relative humidity (RH) is below 20%
= Relative humidity (RH) is above 80%
SUMMER MODE:
The summer mode offers a simple way to maximize your indoor
air quality comfort during the summer months.
- Press the or buttons to enable or disable the
s t
summer mode feature, it will be identified by
SUMMER value will flash.
- Press button to select the desired summer mode.
OK
The wall control returns to the selected operating mode.
ENABLE OR DISABLE THE BACKLIGHT
- Press and hold simultaneously the
for 3 seconds, to enable or disable the LCD display backlight,
the display will flash to identify the desired selection.
(Default mode = LCD backlight is disabled)
IMPORTANT:: A wait time of 10 seconds is required to fully
disable or enable the LCD display backlight.
Note: Pressing the
or
s t
backlight, it remains illuminated for a period of 10 seconds after the
last button is pressed (no matter the button)
FACTORY RESET PROCEDURE:
- Press and hold simultaneously the
buttons for 5 seconds.
Note: The factory default value after reset = "OFF"
- Unplug the ventilation system from the power source for a
period of 30 seconds.
- Proceed and plug in the ventilation system back into the
power source. Proceed to power ON the wall control.
.
mode value will flash.
OK and
t
OK and buttons
s
. The selected
and buttons
s t
button will illuminate to the
, OK and
s t