Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

VIKING RANGE, LLC
MODEL
VIPR102
VIPR102R
VIPR162
VIPR162R
VIPR182
VIPR182R
WARNING - RANGETOPS ONLY: To reduce the risk of burns or ignition of clothing by reaching across burners, an "R" model
downdraft (with remote control) MUST be used with a rangetop. The remote control MUST be mounted in the countertop - at least
4" from the burners. See "INSTALL COOKTOP" section on page 8.
READ AND SAVE THESE INSTRUCTIONS
!
INTENDED FOR DOMESTIC COOKING ONLY
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY
TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer at the address
or telephone number in the warranty.
2. Before servicing or cleaning unit, switch power off at service panel
and lock the service disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a qualifi ed
person(s) in accordance with all applicable codes and standards,
including fi re-rated construction codes and standards.
4. Suffi cient air is needed for proper combustion and exhausting
of gases through the fl ue (chimney) of fuel burning equipment
to prevent backdrafting. Follow the heating equipment
manufacturer's guideline and safety standards such as those
published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and
Air Conditioning Engineers (ASHRAE), and the local code
authorities.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. To reduce the risk of fi re, use only metal ductwork.
8. Do not install this product with the activating switch directly
behind a burner or element. Minimum distance between the
switch and the edge of the burner should be 4 inches.
9. Loose-fi tting or hanging clothing should never be worn when
operating this appliance. They may be ignited by burners/
elements on cooktop.
10. Children should not be left alone or unattended in the area
where this appliance is in use.
11. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
b) Always turn hood ON when cooking at high heat or when
cooking fl aming foods.
c) Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or fi lter.
d) Use proper pan size. Always use cookware appropriate
for the size of the surface element.
WIDTH
30"
30" w/ remote control
36"
36" w/ remote control
48"
48" w/ remote control
BLOWER
(purchase separately)
VIDV500 Interior or VEDV900 Exterior
VIDV500 Interior or VEDV900 Exterior
VIDV500 Interior or VEDV900 Exterior
VIDV500 Interior or VEDV900 Exterior
VIDV500 Interior, VEDV900 Exterior or VEDV1200 Exterior
VIDV500 Interior, VEDV900 Exterior or VEDV1200 Exterior
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
a
FOLLOWING
:
1. SMOTHER FLAMES with a close-fi tting lid, cookie sheet,
or metal tray, then turn off the burner. BE CAREFUL TO
PREVENT BURNS. If the fl ames do not go out immedi
ately, EVACUATE AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN - You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels
- a violent steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher, and you
already know how to operate it.
B. The fi re is small and contained in the area where it
started.
C. The fi re department is being called.
D. You can fi ght the fi re with your back to an exit.
a
Based on "Kitchen Firesafety Tips" published by NFPA.
CAUTION
1. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power
unit.
3. Clean fi lters and grease-laden surfaces frequently.
4. Do not repair or replace any part of this appliance unless
specifi cally recommended in this manual. All other servicing
should be done by a qualifi ed technician.
5. Please read specification label on product for further
information and requirements.
6. DO NOT INSTALL WITH GRILL MODEL RANGETOPS. This
will void the warranty.
7. Models VIPR102SS, VIPR162SS, and VIPR182SS (non-
remote units): DO NOT INSTALL WITH RANGETOPS. This
will void the warranty.
Save this manual for Electrical Inspector and
Use and Care Information on Page 11.
1
Downdraft Ventilators
!
INSTALLER:
Homeowner to use.
HOMEOWNER:
!

Publicité

Table des Matières
loading

Sommaire des Matières pour Viking Range VIPR102SS

  • Page 1 6. DO NOT INSTALL WITH GRILL MODEL RANGETOPS. This will void the warranty. TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: 7. Models VIPR102SS, VIPR162SS, and VIPR182SS (non- a) Never leave surface units unattended at high settings. remote units): DO NOT INSTALL WITH RANGETOPS. This Boilovers cause smoking and greasy spillovers that may will void the warranty.
  • Page 2 1. Refer to the cooktop installation instructions for dimensions of cooktop, countertop cut-out, and cabinet requirements. The Models VIPR102SS and VIPR102RSS will fi t in most 30" wide cabinets the Models VIPR162SS and VIPR162RSS will fi t in most 36" wide cabinets and the Models VIPR182SS and VIPR182RSS will fi...
  • Page 3 VIKING RANGE, LLC Downdraft Ventilators TAKE MEASUREMENTS (CONTINUED) Interior Blower Installation Exterior Blower Installation 2" 2" " " 1" 1" SIDE VIEW SIDE VIEW 7 " 7 " 2 " 2 " OF DOWNDRAFT OF DOWNDRAFT 3 " 3 "...
  • Page 4 VIKING RANGE, LLC Downdraft Ventilators PLAN THE CABINET CUTOUTS Interior Blower Installation Exterior Blower Installation LEFT SIDE LEFT SIDE DISCHARGE DISCHARGE 1 9 ¾ " " CENTER LINE CENTER LINE CENTER CENTER LINES OF COUNTER LINES OF OF COUNTER OF DUCT...
  • Page 5 IMPORTANT - LOCATION OF ELECTRICAL OUTLET: IMPORTANT - LOCATION OF ELECTRICAL OUTLET: If Models VIPR102SS or VIPR102RSS are being installed If Models VIPR102SS or VIPR102RSS are being installed in a 30" wide cabinet...
  • Page 6 VIKING RANGE, LLC Downdraft Ventilators PREPARE THE DOWNDRAFT 10" ROUND Exterior Blower Installation MOTOR DISCHARGE PLUG PLATE NUTS The downdraft is shipped without a blower. Purchase a Model VEDV900 or VEDV1200 Exterior Blower and mount the 10" discharge plate to the downdraft as follows: CLAMP 1.
  • Page 7 VIKING RANGE, LLC Downdraft Ventilators CUT COUNTERTOP OPENING 1. Measure and cut the countertop opening for your width of All Units cooktop and downdraft. Cooktop Width & Model 30" VECU 36" VECU VGSU102 VGSU162 30" VGRT * 36" VGRT * 48"...
  • Page 8 VIKING RANGE, LLC Downdraft Ventilators MOUNT THE UNIT MOUNTING SCREWS All Units LEVELING BRACKET - FLANGE FACING OUT 1. Set downdraft into opening. Extend leveling brackets to fl oor of cabinet so downdraft sits straight. (Note: Leveling brackets can be removed and re-attached in other positions. Bottom fl...
  • Page 9 VIKING RANGE, LLC Downdraft Ventilators INSTALLATION OF REMOTE CONTROL SWITCH 3. Remove the control from the plastic bag. Remove the paper WARNING: To reduce the risk of burns or ignition from the adhesive back of the control, line the control up...
  • Page 10 VIKING RANGE, LLC Downdraft Ventilators This page has been left blank intentionally. BACKSIDE OF REMOTE SWITCH TEMPLATE...
  • Page 11: Install Cooktop

    VIKING RANGE, LLC Downdraft Ventilators INSTALL ELECTRICAL WIRING Interior Blower Installation Exterior Blower Installation CAUTION: All electrical wiring should be done CAUTION: All electrical wiring should be done by a qualifi ed person(s) in accordance with all by a qualifi ed person(s) in accordance with all applicable codes and standards.
  • Page 12 Turns blower ON when vent is UP REMOTE CONTROL and OFF when vent is DOWN. FOR MODELS Note: The UP/DOWN switch for models VIPR102SS, VIPR102RSS VIPR162SS, and VIPR182SS is on the right hand end of the VIPR162RSS top cover. VIPR182RSS DELAY ------------ Allows blower to run for 10 min.
  • Page 13 (12) months from the date of original retail purchase. Viking Range, LLC, warrantor, agrees to repair or replace, at its option, any part which fails or is found to be defective during the warranty period.
  • Page 14: Propriétaire De Maison

    D’UN GRIL. Une telle installation annule votre garantie. DÉCLENCHER SUR LA SURFACE DE CUISSON: 7. Modèles VIPR102SS, VIPR162SS et VIPR182SS (sans télécom- 1. Ne jamais laisser sans surveillance des unités de surface réglées à mande) : NE PAS INSTALLER DANS UNE SURFACE DE CUISSON.
  • Page 15: Préparation

    à effectuer dans le comptoir et les exigences pour l’armoire. Les modèles VIPR102SS et VIPR102RSS s’insèrent dans la plupart des ar- 44,5 mm (1¾ po) moires de 76,2 cm (30 po) de largeur, les modèles VIPR162SS...
  • Page 16: Préparation Des Conduits

    VIKING RANGE, LLC Downdraft Ventilators Ventilateurs encastrés PRISE DES MESURES (SUITE) Installation du ventilateur extérieur Installation du ventilateur intérieur 5 cm (2 po) 5 cm (2 po) 2" 2" " " 2,5 cm 7 mm 7 mm 2,5 cm 1"...
  • Page 17: Ventilateurs Encastrés

    VIKING RANGE, LLC Downdraft Ventilators Ventilateurs encastrés PRÉPARATION DU DÉCOUPAGE DE L’ARMOIRE Installation du ventilateur intérieur Installation du ventilateur extérieur SORTIE À SORTIE À GAUCHE GAUCHE 6 1 , 2 5 0 , 2 1 9 ¾ ( 2 4...
  • Page 18: Préparation Du Câblage

    IMPORTANT – POSITION DE LA PRISE ÉLECTRIQUE : IMPORTANT – POSITION DE LA PRISE ÉLECTRIQUE : Si les modèles VIPR102SS ou VIPR102RSS sont installés Si les modèles VIPR102SS ou VIPR102RSS sont installés dans une armoire de 76,2 cm (30 po) de largeur...
  • Page 19 VIKING RANGE, LLC Downdraft Ventilators Ventilateurs encastrés PRÉPARATION DE LA HOTTE PLAQUE D’ÉVACUA- Installation du ventilateur extérieur COUVERCLE DU TION RONDE DE MOTEUR 25,4 cm (10 po) ÉCROUS La hotte est livrée sans ventilateur. Procurez-vous le ventilateur extérieur modèle VEDV900 ou VEDV1200 et installez la plaque d’évacuation de 25,4 cm (10 po) dans la hotte comme suit :...
  • Page 20: Découpage Du Comptoir

    VIKING RANGE, LLC Ventilateurs encastrés DÉCOUPAGE DU COMPTOIR 1. Mesurez et découpez l’ouverture du comptoir selon la largeur Tous les modèles de la surface de cuisson et de la hotte. Surface de cuisson 76,2 cm (30 po) 91,4 cm (36 po)
  • Page 21: Installation De L'unité

    VIKING RANGE, LLC Downdraft Ventilators Ventilateurs encastrés INSTALLATION DE L’UNITÉ VIS DE MONTAGE Tous les modèles BRIDE DE NIVELLEMENT – REBORD À L’EXTÉRIEUR 1. Placez la hotte dans l’ouverture. Allongez les brides de nivel - lement jusqu’au plancher de l’armoire afi n que la hotte s’appuie bien droite.
  • Page 22: Câblage Électrique

    VIKING RANGE, LLC Downdraft Ventilators Ventilateurs encastrés CÂBLAGE ÉLECTRIQUE Installation du ventilateur intérieur Installation du ventilateur extérieur ATTENTION : Le câblage doit être effectué par un ATTENTION : Le câblage doit être effectué par un électricien qualifi é conformément aux codes et aux électricien qualifi...
  • Page 23: Installation De La Télécommande

    VIKING RANGE, LLC Downdraft Ventilators Ventilateurs encastrés INSTALLATION DE LA TÉLÉCOMMANDE 4. Sortez les deux écrous en nylon du sachet de plastique et AVERTISSEMENT : Pour réduire les risques de brûlure ou que des vêtements s’enfl amment en installez-les sur les goujons de la télécommande en dessous traversant les brûleurs, la télécommande doit être...
  • Page 24: Arrière Du Gabarit De La Télécommande

    VIKING RANGE, LLC Ventilateurs encastrés Downdraft Ventilators Cette page a été laissée en blanc volontairement. ARRIÈRE DU GABARIT DE LA TÉLÉCOMMANDE...
  • Page 25: Fonctionnement

    ABAISSÉ. VIPR102RSS Remarque : Le bouton HAUT/BAS (UP/DOWN) des modèles VIPR162RSS VIPR102SS, VIPR162SS et VIPR182SS est situé à droite de la télé- commande. VIPR182RSS DÉLAI --------------Actionne le ventilateur pendant 10 minutes une fois que l’on a appuyé sur le bouton. Le délai est également activé...
  • Page 26 Viking Range, LLC ou Viking Range, LLC. Précisez le modèle et le numéro de série du produit ainsi que la date originale de votre achat. Pour obtenir le nom de l’agence de réparation agréée de Viking Range, LLC la plus proche, appelez le détaillant chez qui vous avez...
  • Page 27 Nunca deje desatendidas las unidades de la superfi cie cuando estén 7. Modelos VIPR102SS, VIPR162SS y VIPR182SS (unidades no remotas): en ajustes altos de calor. Los alimentos en ebullición provocan derrames NO INSTALE CON ESTUFAS. Esto anulará la garantía.
  • Page 28 1. Consulte las instrucciones de instalación de la estufa para ver las dimensiones de la estufa, la abertura en la superfi cie del gabinete y los requerimientos del gabinete. Los modelos VIPR102SS y VIPR102RSS ajustarán en la mayoría de los gabinetes de 30 pulg. (76 cm) de ancho;...
  • Page 29 VIKING RANGE, LLC Ventiladores de tiro descendente TOME MEDIDAS (CONTINUACIÓN) Instalación del ventilador interior Instalación del ventilador exterior 2 pulg. 2 pulg. (5 cm) (5 cm) 3/8 pulg. 1/4 pulg. (0.95 cm) 1 pulg. (2.54 cm) 1/4 pulg. (.64 cm) 1 pulg.
  • Page 30 VIKING RANGE, LLC Ventiladores de tiro descendente PLANEE LOS CORTES DEL GABINETE Instalación del ventilador interior Instalación del ventilador exterior DESCARGA DEL DESCARGA DEL LADO IZQUIERDA LADO IZQUIERDA ¾ p u l g . p u l g ( 5 0 ( 6 1 .
  • Page 31 IMPORTANTE - UBICACIÓN DEL TOMACORRIENTE ELÉCTRICO: TOMACORRIENTE ELÉCTRICO: Si los modelos VIPR102SS o VIPR102RSS se van a instalar en un Si los modelos VIPR102SS o VIPR102RSS se van a instalar en un gabinete de 30 pulg. (75 cm) de ancho…...
  • Page 32 VIKING RANGE, LLC Ventiladores de tiro descendente PREPARE EL TIRO DESCENDENTE PLACA DEL CONDUCTO Instalación del ventilador exterior ENCHUFE DEL REDONDO DE MOTOR 10 pulg. (25 cm) TUERCAS El tiro descendente se envía sin ventilador. Compre un ventilador exterior modelo VEDV900 o VEDV1200 y monte la placa de descarga de 10 pulg.
  • Page 33 VIKING RANGE, LLC Ventiladores de tiro descendente HAGA LA ABERTURA DE LA SUPERFICIE DEL GABINETE Todas las unidades 1. Mida y corte la abertura de la superfi cie del gabinete según el ancho de la estufa y del tiro descendente.
  • Page 34 VIKING RANGE, LLC Ventiladores de tiro descendente MONTE LA UNIDAD TORNILLOS DE MONTAJE Todas las unidades SOPORTE DE NIVELACIÓN, REBORDE ORIENTADO HACIA AFUERA 1. Coloque el tiro descendente en la abertura. Extienda los soportes de nivelación al piso del gabinete para que el tiro descendente quede recto.
  • Page 35 VIKING RANGE, LLC Ventiladores de tiro descendente INSTALACIÓN DEL INTERRUPTOR DEL CONTROL REMOTO ADVERTENCIA: Para reducir el riesgo de quemadoras o de 3. Saque el control de la bolsa de plástico. Quite el papel del respaldo adhesivo del control, alinee el control con los tres orifi cios y coloque el que se incendie la ropa al pasar sobre las hornillas, el control control de tal manera que quede paralelo con el frente del gabinete.
  • Page 36 VIKING RANGE, LLC Ventiladores de tiro descendente Esta página se ha dejado en blanco intencionalmente. PARTE POSTERIOR DE LA PLANTILLA DEL CONMUTADOR REMOTO...
  • Page 37 VIKING RANGE, LLC Ventiladores de tiro descendente INSTALE EL CABLEADO ELÉCTRICO Instalación del ventilador interior Instalación del ventilador exterior PRECAUCIÓN: Una o más personas califi cadas deben reali- PRECAUCIÓN: Una o más personas califi cadas deben reali- zar el trabajo de cableado eléctrico, de acuerdo con todos zar el trabajo de cableado eléctrico, de acuerdo con todos...
  • Page 38: Uso Y Cuidado

    ARRIBA y lo CONTROL REMOTO apaga cuando el sistema está ABAJO. PARA LOS MODELOS Nota: El interruptor ARRIBA/ABAJO para los modelos VIPR102SS, VIPR102RSS VIPR162SS y VIPR182SS se encuentra en la parte inferior derecha de VIPR162RSS la cubierta superior.
  • Page 39 Según los términos de esta garantía, el servicio debe ser realizado por un agente o representante de servicio autorizado por la fábrica de Viking Range, LLC. El servicio se brindará en horario comercial normal, y la mano de obra realizada en horas extra o a tarifas de primer nivel no quedará...
  • Page 40 Las especifi caciones están sujetas a cambios sin previo aviso. Si desea más información sobre el producto, llame al 1-845-4641, o visite el sitio web en http://www.vikingrange.com. F20073C SP 99044605C...

Ce manuel est également adapté pour:

Vipr162ssVipr102rssVipr182ssVipr182rssVipr162rss

Table des Matières