ANSMANN POWERLIGHT 5.1 Manuel D'utilisation page 3

GB
Working spotlamp
Be sure tO read tHe user's instructiOns BefOre starting tO
use tHe laMp
tecHnical data:
> lamp equipment:
Main lamp: Xenon, 6.5 v, 5 w (item no. 0827 820 001).
low-power lamp: luxeon led, service life > 50,000 h.
> Battery: sealed lead-gel battery, 6 v, 4.5 aH, rechargeable, maintenance-free
> charging time: max. 4.5 h.
> Battery life:
Main lamp Xenon > 5 h., thereafter automatic switchover to
luxeon led > 1 h
luxeon led about 20 h.
luxeon led flashing about 40 h
> protection class ii.
> protection type: ip65.
> Operating /storage temperature: –20°c to +50°c.
cHarging:
> cHarge tHe laMp fully BefOre first using it.
> charge the lamp fully before it is to be stored for an extended period.
> charging options:
Mains charger: 230 v, 50 Hz.
Motor vehicle charger:12 v to 24 v - ac / dc (max. 2 a).
warning: it is essential to ensure that the cigar-lighter is still live even when the ignition
key is removed from the ignition switch. if this is not the case, the charging cable must
be protected by a 3-amp fuse and connected directly to the battery.
> the led will light yellOw to indicate that the lamp is being charged.
the led changes to green as soon as the battery is charged.
there is in parallel a capacity display using five leds.
> to maintain its charge, the lamp should always be parked in the wall-mounted holder
when not in use. automatic discharging and a reduction in the battery capacity
will thus be avoided. the spotlamp has an automatic charging voltage monitor Ô and
continuous charging is thus possible.
> when removed from the wall-holder, the lamp switches on as a functional
check.
OperatiOn Of tHe laMp:
press the selector switch once:
press the selector switch twice:
press the selector switch 3 x:
press the selector switch 4 x:
the energy-saving lamp (led) is actuated automatically if the filament in the main lamp
fails and also before reaching the low-battery protection point. Before reaching the low-
battery voltage, the lamp automatically switches to energy-saving mode (led), with a
residual lighting duration > 1 h. the spotlamp switches itself off automatically as soon as
the low-battery voltage is reached.
capacity display:
when the spotlamp is in operation, the remaining battery capacity is signalled by five
leds, as follows:
3 green leds: > 75%, > 50%, > 25%
1 yellOw led: < 25%
1 red led: < 10%
eMergency ligHting functiOn:
while the lamp is parked in the wall-holder for charging, should there be a mains power
failure, the main beam will light up and remain lit until either the mains power is restored
or the low-power limit of the battery is reached.
it is possible to switch the spotlamp off manually.
repair and Maintenance:
servicing operations may only be carried out by properly-trained electrical experts.
Only original replacement parts are to be used.
Main beam is on
energy-saving lamp (led) is on
energy-saving lamp (led) flashes
spotlamp is switched off
cHanging tHe Battery:
please prOceed as fOllOws:
> Loosen the four screws left, right and at the bottom of the housing.
> Carefully remove the rear panel from the housing.
> Remove the old battery.
> Remove the red (+) and black (-) cable-tags from the battery.
> Install the new battery and then push it into place.
> Warning: do not short-circuit the battery!
> Re-assemble the lamp in the reverse order.
Exhausted batteries must be recycled in accordance with local regulations, and must NOT be
discarded with domestic waste!
spOtlaMp: general arrangeMent:
1. Belt-hook for attaching the spotlamp by a snap-hook.
2. Mode selector switch.
3. charger input 12 v ... 24 v.
4. wall-holder with 4 fixing holes. fixing screws andwall-plugs are included.
5. spotlight head with carrying handle (the head can be swivelled forwards by
30° and backwards by 90°).
6. guide-hooks for holding diffuser disc.
7. Holder for two diffuser discs (white and orange – supplied).
8. Housing with integrated lamp controls and charging electronics.
BulB cHanging
please fOllOw tHe instructiOns BelOw:
> to open the housing, turn the lamp surround ring anticlockwise
> carefully remove lamp surround ring
> take care when removing the reflector from the lamp head
> turn the bulb gently until the v-shape cut-out is at the top
> remove the bulb towards you
> Hold the new bulb with a cloth at all times. push it carefully into the opening
and lock it in place with a half a revolution clockwise
> the v-shaped cut-out should now point downwards
> carefully replace the reflector back in the lamp head. important: the openings
for the bulbs must be in the correct positions
> refit the lamp surround ring carefully ensuring that the threads mate correctly.
turn it clockwise until it hits the stop