Publicité
Les langues disponibles
Les langues disponibles
Motoverrou
MVM, MVA and MVM2C
®
IP protection : IP57
Imput voltage: 12 to 18V AC/DC
Consumption in rush: 410 mA max.
Consumption in stand-by: 20 mA
Consumption of the operating : 10 mA
Audible signal when door unlocked with beep around
Relcoking if door not openned after 5 beeps (8s)
The motorized lock has a built-in position sensor to detect the strike plate position and the to lock whe the door is closed. To unlock the door, use the knob or the access con-
trol system (Keypad,proximity reader,push button...)When the door is closed, the bolt must be allgned to the strike plate. A misalignement will cause several thrown of the
bolt until the bolt is aligned correctly.
1] MOUNTING KIT
Lock
Strike plate
Bracket
1
1
1
2] WIRE
Control isolated by the
12 to 18 V AC/DC -
6 to 10 mA
+
contact
- Push button
- Relay board
+
-
-
- Access control
Control isolated by the
12 to 18 V AC/DC -
6 to 10 mA
+
contact
+
-
-
3] MOUNTING INTRODUCTION
The Motoverrou
is mounting on the door
®
126
96
30
80
22
1
2
93
1. Remove the two screews on the side of the strike plate
2. Mount the bracket of the strike plate on the door jamb (schéma 2)
3. Mount the strike plate on the bracket (shéma 3)
4. Make sure that the magnet sensor of the strike plateis in front of the position sensorof the lock (schéma 4)
5. During the fitting, put the mounting guide in the strike plate, remove when installationis finished and that correct
locking/unlocking operations has been done on the lock. (schéma 5)
Cylinder and accessories fitting
DOOR THICKNESS 80 MM MAX.
M4 SCREW FOR FIXING PLATE
M5 SCREEW BREAKABLE ACCORDING TO THE DOOR THICKNESS
FOLLOWER BREAKABLE ACCORDING TO THE DOOR THICKNESS
Top of view of the door
IP57
Cylinder
Keys
Washer
1
3
1
+
- 12 to 18 V AC/DC
+
+
-
- 12 to 18 V AC/DC
+
+
95
58
58
21
21
15
15
28
28
36
95
65
95
65
36
28
28
21
21
3
SCHEMA 3
SCHEMA 2
SCHEMA 3
SCHEMA 2
SCHEMA 4
CONTACT REED EN VIS A VIS
SCHEMA 4
CONTACT REED EN VIS A VIS
POSITION SENSOR AND MAGNET SENSOR
POSITION SENSOR AND MAGNET SENSOR
IMPORTANT
CDVI_IM_MVA-MVM-MVM2C 1C A03 FR-EN 03 - G0301FR1010V03
MVM/MVA/MVM2C
Motorized lock
24,9
8
24,9
130
MVM, Motorized lock with knob
Mounting
Fixing plate
guide
1
1
Control not isolated by the
contact
+ -
-
Control not isolated by the
58
contact
+ -
-
21
15
28
65
28
21
SCHEMA 3
SCHEMA 2
4
SCHEMA 4
Position sensor and
CONTACT REED EN VIS A VIS
POSITION SENSOR AND MAGNET SENSOR
magnet sensor
Mounting complete top view
8
8
24,9
130
MVA, Motorized lock without knob
Ce document est la propritété exclusive de CDVI, il ne peut être communiqué à des tiers sans son autorisation.
Plan M2434
This document is the exclusive property of CDVI and it may not be disclosed to others without permission.
SCALE 1:1
Edition 02
MVM
Date 17/05/2019
Mechanical Engraving
A3
CA: F0529000018
Material : ...
31, av du Gal Leclerc
General tol :
0.1
Surface roughness: Ra 3,2
93691 PANTIN CEDEX
F R A N C E
Tel : 33(0)148910102
3
DES.: W. Sainvil
Vol. (mm
) :
Mass (g) :
Fax : 33(0)148912121
www.cdvi.com
L - -
L
+
+
Screws
Zinc screws
Terminal
adjustable
strike plate
lenght
mounting
1
2
5
+
-
12 to 18 V AC/DC
+
+
-
-
12 to 18 V AC/DC
+
+
36
5
MOUNTING GUIDE FOR
POSITIONNING THE BOLT
IN THE STRIKE PLATE
ONLY. REMOVE AFTER
LOCK IS MOUNTED.
FOLLOWER
IMPORTANT
Insert the followers as (shown next) in the
follower access broke of the lock bolt "pulled in"
activate manually the lock from knob to make
sure that the follower is not turning.
Verify the cylinder with the key to insure cor-
rect locking/unlocking
Cylinder
EN
24,9
8
Ce document est la propritété exclusive de CDVI, il ne peut être communiqué à des tiers sans son
This document is the exclusive property of CDVI and it may not be disclosed to others without perm
SC
MVA
Mechanical Engraving
Material : ...
General tol :
0.1
Surface roughness: Ra 3,2
3
DES.: W. Sainvil
Vol. (mm
) :
Mass (g) :
Spare
Screws lock
screws
mounting
2
4
CONNEXION
FEMALE TERMINAL
CONNECTEUR FEMELLE
Publicité
