Interlogix DI601-WT Guide D'installation Et D'utilisation page 3

When the battery is fitted, close the battery compartment (see
Figure 5), and the walk tester is ready for use.
Using the walk tester
Remove the cover from the detector housing by loosening the
stainless steel screw at the bottom of the detector and pressing
the sides of the cover as shown in Figure 7.
This allows access to the programming button shown in
Figure 8 (and lets you verify the presence of the IR emitting
LED).
Put the detector into walk test mode by pressing the
programming button once (see Figure 8). The detector blue
LED will then flash out its current settings. Wait for the flashing
sequence to finish. The detector is now in walk test mode, and
remains in that state for five minutes after the last detection,
thereafter it reverts to normal mode. Walk test can be
cancelled at any time by pressing the programming button
twice.
Hook the mounting bracket of the cradle onto the bottom lip of
the detector and replace the cover. Tighten the screw on the
front cover of the detector to firmly hold the mounting bracket
between the two edges (see Figure 9).
Turn the walk tester on.
The walk tester illuminates and sounds every time the detector
is activated.
For more information on the walk test procedure please refer to
the relevant DI601/DDI602 detector installation sheet.
When finished testing, turn off the walk tester and remove it
and the cradle from the detector. Tighten the screw on the
base of the detector. The DI/DDI series outdoor detector is
now ready.
Specifications
Power 9 VDC (PP3 Cell)
Note: Battery is not included.
Current:
Standby 0.5 mA
Operating 30 mA
−20 to +55°C
Operating
temperature
Protection Please note that the walk tester is not waterproof
and should not be used in wet weather conditions.
The housing is made from high impact ABS plastic.
Dimensions 118 x 47 x 25 mm
Regulatory information
Manufacturer UTC Fire & Security Americas Corporation, Inc.
1275 Red Fox Rd., Arden Hills, MN 55112-6943, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Certification
P/N 1069716 (ML) • REV B • ISS 05NOV13
FCC This device complies with part 15 of the FCC Rules.
compliance Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
The manufacturer declares that the product supplied
is compliant with the provisions of the EMC Directive
89/336/EEC amended 92/31/EEC for Electromagnetic
Compatibility, and the Restriction of Hazardous
Substances Directive (RoHS) 2002/95/EC. A
Declaration of Conformity in accordance with the
above directives is held on file with the manufacturer.
2002/96/EC (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more
information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains
a battery that cannot be disposed of as unsorted
municipal waste in the European Union. See the
product documentation for specific battery information.
The battery is marked with this symbol, which may
include lettering to indicate cadmium (Cd), lead (Pb),
or mercury (Hg). For proper recycling, return the
battery to your supplier or to a designated collection
point. For more information see: www.recyclethis.info.
Contact information
www.utcfireandsecurity.com or www.interlogix.com
For customer support, see www.utcfssecurityproducts.eu
DE: Installations- und
Benutzerhandbuch
Beschreibung
Bei dem Gehtest-Prüfgerät DI601-WT (siehe Abbildung 1)
handelt es sich um ein Installationswerkzeug zur Unterstützung
des Installateurs beim Einrichten des
Außenbewegungsmelders DI601/DDI602 vor Ort.
Jeder Außenbewegungsmelder der DI/DDI Serie weist eine
Infrarot-LED auf. Bei Aktivierung sendet die LED ein Signal.
Das Gehtest-Prüfgerät empfängt dieses Signal, woraufhin am
Prüfgerät eine helle weiße LED blinkt und aus einem
Piezolautsprecher ein Ton erklingt.
Unter Normalbedingungen können die LED und der Ton aus
einer Entfernung von 50 m gesehen bzw. gehört werden.
Abbildungen
Abbildung 1: Gehtest-Prüfgerät
Abbildung 2: Halterung des Gehtest-Prüfgeräts
Abbildung 3: Anschluss für 9-V-Blockbatterie
Abbildung 4: Eingesetzte 9-V-Blockbatterie
Abbildung 5: Entfernen der Batteriefachabdeckung
3 / 12