Table des Matières
Publicité
12
TKT Series
Thank you for choosing a TANNOY loudspeaker product for your application. If you would like further
information about this or any other product, please visit our website at musictribe.com.
Unpacking the Loudspeaker
After unpacking the unit, please check carefully for damage. If damage is found, please notify your
supplier at once. You, the consignee, must instigate any claim. Please retain all packaging in case of
future return shipment.
System Requirements
TKT are passive 2-way and 3-way loudspeakers, all of which can be driven directly from a single amplifier
channel with no controller. For optimum performance or for use with a subwoofer, they require 1 amplifier
channel and 1 controller channel. The input signal is divided between the low-frequency and high-frequency
drivers internally with a passive crossover.
Amplifier Considerations
10
TKT Series
The TKT series loudspeaker enclosures should be driven by high-quality power amplifiers designed for true
professional use. Power amplifiers should be capable of delivering long term broadband power equal to half
er Considerations
the loudspeaker's peak power rating at its stated nominal impedance. The use of underpowered amplifiers
The TKT series loudspeaker enclosures should be driven by high-q
mustbe avoided as heavily clipped signals can cause permanent loudspeaker damage. Limiters, crossovers
delivering long term broadband power equal to half the loudspeaker's peak power rating at its stated nominal impedance. The use
and equalisation points must be set in accordance with the specifications provided below. This will ensure the
be avoided as heavily clipped signals can cause permanent loudspeaker damage. Limiters, crossovers and equalisation points must be set in accordance with the
optimum sound quality and long-term reliability as well as protection from damage.
Model
TKT105
Minimum
Continuous RMS
150 W
300 W
Power
Peak
600 W
1200 W
Crossovers
Crossovers
TKT Series loudspeakers are supplied as standard for passive operation via the internal crossover network. If higher peak outputs and additional low frequency output
is required, then the TKT series can be used in conjunction with the Tannoy SC1 digital controller. Each input on the network enabled VNET SC1 has gain control and
TKT Series loudspeakers are supplied as standard for passive operation via the internal crossover network.
LF and HF shelving response. The unique routing engine will allow any input to be sent to any output.
If higher peak outputs and additional low frequency output is required, then the TKT series can be used in
conjunction with the Tannoy SC1 digital controller. Each input on the network enabled VNET SC1 has gain
delay (200 ms per channel) and a 4-band parametric EQ for speaker management. Four high performance limiters are also available.
control and 4 bands of parametric EQ with bands 1 and 4 of ering settings for LF and HF shelving response.
The unique routing engine will allow any input to be sent to any output.Various i lter types are available on
all outputs which can be coni gured as 2-, 3- or 4-way crossovers. All output channels feature an independent
speaker alignment delay (200 ms per channel) and a 4-band parametric EQ for speaker management.
Four high performance limiters are lso available.
damage.
TKT102
TKT122
500 W
2000 W
ature an independent speaker alignment
Connections
TKT105 connection is made via screw terminal binding posts. TKT102 and TKT122 have inputs on 1 x SpeakON
4-pole connector and 1 x barrier strip terminal.
Connections
Binding post terminals are capable of accepting cables with a conductor of up to 4 mm sq CSA (AWG 12). Red
TKT105 connection is made via screw terminal binding posts. TKT102 and TKT122 have inputs on 1 x SpeakON 4-pole connector and 1 x barrier strip terminal.
is positive and black is negative. The SpeakON connectors will accept wire up to 4 mm sq CSA (AWG 12) with
Binding post terminals are capable of accepting cables with a conductor of up to 4 mm sq CSA (AWG 12). Red is positive and black is negative. The SpeakON connectors
an outside diameter of up to 15 mm and a current rating of 30 A. Tannoy have adopted the conventional
will accept wire up to 4 mm sq CSA (AWG 12) with an outside diameter of up to 15 mm and a current rating of 30 A. Tannoy have adopted the conventional wiring
wiring standard for the TKT series product: pin 1+ is positive pin 1- is negative. Barrier strips accept wire up to
standard for the TKT series product: pin 1+ is positive pin 1- is negative. Barrier strips accept wire up to 4 mm sq CSA (AWG 12). Barrier strip polarity is as indicated.
4 mm sq CSA (AWG 12). Barrier strip polarity is as indicated.
Models: TKT105
M
d o
l e
R
a e
P r
n a
l e
o C
n n
c e
Passive
Red - Positive
Black - Negative
Models: TKT102, TKT122
Model
Rear Panel
Passive
PASSIVE, Input Full Range +
PASSIVE, Input Full Range -
PASSIVE, Input Full Range -
PASSIVE, Input Full Range +
Quick Start Guide
Quick Start Guide
r o t
Internal Connections
HPF
HF
Red
Binding
MPF
MF
Post
Input
Black
LPF
LF
Connector
Internal Connections
1 +
NL4
1 +
Input/
2 +
Link
2 -
1-
1+
1 +
Barrier
1 +
Strip
Input/
2-
2 +
2+
Link
2 -
1+
1-
2+
2-
13
11
HF
LF
Publicité
Table des Matières
