Programming Track Numbers - Philips AX7200 Mode D'emploi

SELECTING A TRACK AND SEARCHING
Selecting a track during playback
• Briefly press ∞ or § once or several times to skip
to the current, previous or next track.
yPlayback continues with the selected track, and
the track number is displayed.
Selecting a track when playback is stopped
1 Briefly press ∞ or § once or several times to select the desired track. The
track number is displayed.
2 Press 2; to start CD play.
yPlayback starts with the selected track.
Searching for a passage during playback
1 Keep ∞ or § pressed to find a particular passage in
a backward or forward direction.
ySearching starts while playback continues at
low volume. After 2 seconds the search speeds
up.
2 Release the button when you reach the desired passage.
yPlayback continues from this position.
Notes: – If the player is in SCAN mode (see MODE chapter), searching is not
possible.
– In shuffle, shuffle repeat all or repeat
while playing a program, searching is only possible within the
particular track.

PROGRAMMING TRACK NUMBERS

(remote control only)
You can store up to 30 tracks to play in a program. A single track may be stored
more than once in the program.
1 While playback is stopped, select a track with
∞ or §.
2 Press PROG to store the track.
yprog lights up; the track number
programmed and P with the total number of
stored tracks are displayed.
3 Select and store all desired tracks in this way.
4 Press 2; to start playback of your selected tracks.
yprog is shown and playback starts.
• You can review the program by pressing PROG
for more than 2 seconds.
yThe display shows all the stored tracks in sequence.
Notes: – If you press PROG and there is no track selected,
displayed.
– If you try to store more than 30 tracks, FULL is displayed.
Clearing the program
• While playback is stopped, press 9 to clear program.
yCLEAr
is displayed once, prog goes off, and
the program is cleared.
Note: The program will also be cleared if the power supply is interrupted, or if the
CD-player lid is opened, or if the set switches off automatically.
mode (see MODE chapter), or
SE
LECt is
RESUME AND HOLD
You can interrupt playback and continue (even after an
extended period of time) from the position where
playback stopped (RESUME) and you can lock all buttons
of the set so that no action will be executed (HOLD).
Use the OFF–RESUME–HOLD slider for these functions.
RESUME – continuing from where you have stopped
1 Switch the slider to RESUME during playback to activate RESUME.
yDisplay: resume.
2 Press 9 whenever you want to stop playback.
3 Press 2; whenever you want to resume playback.
yDisplay: resume. Playback continues from
where you have stopped.
• To deactivate RESUME, switch the slider to OFF.
yDisplay: resume goes off.
HOLD – locking all buttons
You can lock the buttons of the set by switching the
slider to HOLD. With HOLD activated, you can avoid
accidental activation of other functions.
1 Switch the slider to HOLD to activate HOLD.
yAll buttons are locked. HoLd is shown when you press any button
set. If the set is switched off, HoLd will be shown only when 2; is
the
pressed on the set.
2 To deactivate HOLD, switch the slider to OFF.
Note: For convenience, the remote control buttons override the HOLD function on
the set.
SELECTING DIFFERENT PLAY OPTIONS − MODE
(remote control only)
It is possible to play tracks in random order, to repeat a single track or the entire
CD, and to play the first few seconds of each track.
1 Press MODE during playback as often as required in
order to activate one of the following 'modes'. The
active mode is shown in the display.
yshuffle: All tracks of the CD are played in
random order until all of them have been played
once.
yshuffle repeat all: All tracks of the CD are
played repeatedly in random order.
yrepeat: The current track is played repeatedly.
yrepeat all: The entire CD is played repeatedly.
ySCAn: The first 10 seconds of
remaining tracks are played in sequence.
2 Playback starts in the chosen mode after 2 seconds.
• To return to normal playback, press MODE repeatedly until the display shows
no active modes.
DBB
Bass adjustment (remote control only)
1 Press DBB once or more to select the bass
enhancement options:
y
moderate bass enhancement is activated.
y
strong bass enhancement is activated.
2 Press DBB again to switch off the bass enhancement options.
y
or disappears.
each of the
on