Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
English
for the location of the mounting screws on the wall. Mount
the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
Intended Use
These drills/drivers/hammerdrills are designed
for professional drilling, screwdriving and
hammerdrilling applications.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
These drills/drivers/hammerdrills are professional power
tools. DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Installing a Bit or Accessory into a Keyless
Chuck (Fig. B)
WARNING: Do not attempt to tighten drill bits (or
any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck
and personal injury may result. Always lock off trigger
switch and disconnect tool from power source when
changing acces sories.
WARNING: Always ensure the bit is secure before
starting the tool. A loose bit may eject from tool
causing possible personal injury.
To insert a drill bit or other accessory, follow these steps.
1. Turn tool off and remove battery pack.
2. Grasp the black sleeve of the chuck with one hand
and use the other hand to secure the tool. Rotate the
sleeve counterclockwise far enough to accept the
desired accessory.
3. Insert the accessory about 3/4" (19 mm) into the
chuck
8
and tighten securely by rotating the chuck
sleeve
9
clockwise with one hand while holding the
tool with the other. Your tool is equipped with an
automatic spindle lock mechanism. This allows you to
open and close the chuck with one hand.
Be sure to tighten chuck with one hand on the chuck sleeve
and one hand holding the tool for maximum tightness.
To release the accessory, repeat steps 1 and 2 above.
8
Fig. B
9
8
Speed Selection (Fig. A)
The tool features two speed settings for greater versatility.
nOTE: Do not change speeds when the tool is running.
Always allow the tool to come to a complete stop before
changing speed.
1. To select speed 1 (higher torque setting), slide the
speed selector
6
back (away from the chuck).
2. To select speed 2 (lower torque setting), slide the speed
selector forward (towards the chuck).
If the tool does not change speeds, confirm that the speed
selection switch is completely engaged in the forward or
back position.
Mode Selection (Fig. A)
The mode selection collar
5
the correct operating mode depending upon the
planned application.
To select, rotate the collar until the desired symbol aligns
with the arrow.
WARNING: When the torque adjustment collar is
in the drill or hammerdrill positions, the drill will not
clutch. The drill may stall if overloaded, causing a
sudden twist.
symbol
1–15
Screwdriving (higher number = greater torque)
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove loads and
fastenersremove the battery pack before
making any adjustments or removing/installing
attachments or accessories. An accidental start-
upactuation can cause injury.
Installing and Removing the Battery Pack
(Fig. C)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
1
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in
the tool and ensure that it does not disengage.
can be used to select
Mode
Drilling
into the tool handle, align the
Publicité
Table des Matières
